FXLS93421 datasheet(47/254 Pages) NXP

47 / 254 page

NXP Semiconductors

FXLS9xxxx

Dual channel inertial sensor

INTREGA_ERR

Error condition

No error detected

Internal Analog Regulator Voltage Out of Range

Table 58. Internal analog regulator voltage out of range error (INTREGA_ERR)

11.2.2.13 Internal digital regulator voltage out of range error (INTREG_ERR)

The internal digital regulator voltage out of range error bit is set if the internal digital

regulator voltage falls outside expected limits. A common timer is used for all error bits

in the DEVSTAT1 register. If any supply error is present, the timer is reset to tUVOV_RCV.

This bit is cleared based on the state of the SUP_ERR_DIS bit in the DEVLOCK_WR

INTREG_ERR

Error condition

No error detected

Internal Digital Regulator Voltage Out of Range

Table 59. Internal digital regulator voltage out of range error (INTREG_ERR)

11.2.2.14 Internal OTP regulator voltage out of range error (INTREGF_ERR)

The internal OTP regulator voltage out of range error bit is set if the internal OTP

regulator voltage falls outside expected limits. A common timer is used for all error bits

in the DEVSTAT1 register. If any supply error is present, the timer is reset to tUVOV_RCV.

This bit is cleared based on the state of the SUP_ERR_DIS bit in the DEVLOCK_WR

INTREGF_ERR

Error condition

No error detected

Internal OTP Regulator Voltage Out of Range

Table 60. Internal OTP regulator voltage out of range error (INTREGF_ERR)

11.2.2.15 Continuity monitor error (CONT_ERR)

The continuity monitor passes a low current through a connection around the perimeter

of the device and monitors the continuity of the connection. The error bit is set if a

discontinuity is detected in the connection. A common timer is used for all error bits in the

DEVSTAT1 register. If the CONT_ERR bit is set, the timer is reset to tUVOV_RCV. This bit

is cleared based on the state of the SUP_ERR_DIS bit in the DEVLOCK_WR register as

shown in Section 11.2.2.5.

CONT_ERR

Error condition

No error detected

Error detected in the continuity of the monitor circuit

Table 61. Continuity monitor error (CONT_ERR)

11.2.2.16 NXP OTP array error (F_OTP_ERR)

The factory OTP array error bit is set if a fault is detected in the factory OTP array. This

error is cleared by a device reset. See Section 11.2.15.2 for details on a method to

disable the automatic clearing of this error in PSI5 mode.

FXLS9xxxx

All information provided in this document is subject to legal disclaimers.

Product data sheet

Rev. 6 — 8 February 2021

47 / 254

FXLS93421 bảng dữ liệu(PDF) 47 Page - NXP Semiconductors

FXLS93421 bảng dữ liệu(HTML) 47 Page - NXP Semiconductors

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

bảng dữ liệu tải về

Link URL