HCS08 datasheet(187/374 Pages) NXP

187 / 374 page

Multi-Purpose Clock Generator (S08MCGV1)

MC9S08JM60 Series Data Sheet, Rev. 5

Freescale Semiconductor

187

12.3.4

MCG Status and Control Register (MCGSC)

432

LOLS

LOCK

PLLST

IREFST

CLKST

OSCINIT

FTRIM

POR:

Reset:

Figure 12-6. MCG Status and Control Register (MCGSC)

Table 12-4. MCG Status and Control Register Field Descriptions

Field

Description

LOLS

Loss of Lock Status — This bit is a sticky indication of lock status for the FLL or PLL. LOLS is set when lock

detection is enabled and after acquiring lock, the FLL or PLL output frequency has fallen outside the lock exit

frequency tolerance, Dunl. LOLIE determines whether an interrupt request is made when set. LOLS is cleared by

reset or by writing a logic 1 to LOLS when LOLS is set. Writing a logic 0 to LOLS has no effect.

0 FLL or PLL has not lost lock since LOLS was last cleared.

1 FLL or PLL has lost lock since LOLS was last cleared.

LOCK

Lock Status — Indicates whether the FLL or PLL has acquired lock. Lock detection is disabled when both the

FLL and PLL are disabled. If the lock status bit is set then changing the value of any of the following bits IREFS,

PLLS, RDIV[2:0], TRIM[7:0] (if in FEI or FBI modes), or VDIV[3:0] (if in PBE or PEE modes), will cause the lock

status bit to clear and stay cleared until the FLL or PLL has reacquired lock. Stop mode entry will also cause the

lock status bit to clear and stay cleared until the FLL or PLL has reacquired lock. Entry into BLPI or BLPE mode

will also cause the lock status bit to clear and stay cleared until the MCG has exited these modes and the FLL or

PLL has reacquired lock.

0 FLL or PLL is currently unlocked.

1 FLL or PLL is currently locked.

PLLST

PLL Select Status — The PLLST bit indicates the current source for the PLLS clock. The PLLST bit does not

update immediately after a write to the PLLS bit due to internal synchronization between clock domains.

0 Source of PLLS clock is FLL clock.

1 Source of PLLS clock is PLL clock.

IREFST

Internal Reference Status — The IREFST bit indicates the current source for the reference clock. The IREFST

bit does not update immediately after a write to the IREFS bit due to internal synchronization between clock

domains.

0 Source of reference clock is external reference clock (oscillator or external clock source as determined by the

EREFS bit in the MCGC2 register).

1 Source of reference clock is internal reference clock.

3:2

CLKST

Clock Mode Status — The CLKST bits indicate the current clock mode. The CLKST bits do not update

immediately after a write to the CLKS bits due to internal synchronization between clock domains.

Encoding 0 — Output of FLL is selected.

Encoding 1 — Internal reference clock is selected.

Encoding 2 — External reference clock is selected.

Encoding 3 — Output of PLL is selected.

HCS08 bảng dữ liệu(PDF) 187 Page - NXP Semiconductors

HCS08 bảng dữ liệu(HTML) 187 Page - NXP Semiconductors

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

bảng dữ liệu tải về

Link URL