HCS08 datasheet(59/374 Pages) NXP

59 / 374 page

Chapter 4 Memory

MC9S08JM60 Series Data Sheet, Rev. 5

Freescale Semiconductor

4.7.1

Flash Clock Divider Register (FCDIV)

Bit 7 of this register is a read-only status flag. Bits 6 through 0 may be read at any time but can be written

only one time. Before any erase or programming operations are possible, write to this register to set the

frequency of the clock for the nonvolatile memory system within acceptable limits.

if PRDIV8 = 0 — fFCLK = fBus ÷ ([DIV5:DIV0] + 1)

Eqn. 4-1

if PRDIV8 = 1 — fFCLK = fBus ÷ (8 × ([DIV5:DIV0] + 1))

Eqn. 4-2

Table 4-7 shows the appropriate values for PRDIV8 and DIV5:DIV0 for selected bus frequencies.

321

RDIVLD

PRDIV8

DIV5

DIV4

DIV3

DIV2

DIV1

DIV0

Reset

000

= Unimplemented or Reserved

Figure 4-5. Flash Clock Divider Register (FCDIV)

Table 4-6. FCDIV Register Field Descriptions

Field

Description

DIVLD

Divisor Loaded Status Flag — When set, this read-only status flag indicates that the FCDIV register has been

written since reset. Reset clears this bit and the first write to this register causes this bit to become set regardless

of the data written.

0 FCDIV has not been written since reset; erase and program operations disabled for flash.

1 FCDIV has been written since reset; erase and program operations enabled for flash.

PRDIV8

Prescale (Divide) Flash Clock by 8

0 Clock input to the flash clock divider is the bus rate clock.

1 Clock input to the flash clock divider is the bus rate clock divided by 8.

5:0

DIV[5:0]

Divisor for Flash Clock Divider — The flash clock divider divides the bus rate clock (or the bus rate clock

divided by 8 if PRDIV8 = 1) by the value in the 6-bit DIV5:DIV0 field plus one. The resulting frequency of the

internal flash clock must fall within the range of 200 kHz to 150 kHz for proper flash operations. Program/Erase

timing pulses are one cycle of this internal flash clock which corresponds to a range of 5

μs to 6.7 μs. The

automated programming logic uses an integer number of these pulses to complete an erase or program

operation. See Equation 4-1, Equation 4-2, and Table 4-6.

HCS08 bảng dữ liệu(PDF) 59 Page - NXP Semiconductors

HCS08 bảng dữ liệu(HTML) 59 Page - NXP Semiconductors

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

bảng dữ liệu tải về

Link URL