HCS08 datasheet(230/316 Pages) NXP

230 / 316 page

Serial Peripheral Interface (S08SPIV3)

MC9S08SG8 MCU Series Data Sheet, Rev.8

230

Freescale Semiconductor

15.5

Functional Description

An SPI transfer is initiated by checking for the SPI transmit buffer empty flag (SPTEF = 1) and then

writing a byte of data to the SPI data register (SPID) in the master SPI device. When the SPI shift register

is available, this byte of data is moved from the transmit data buffer to the shifter, SPTEF is set to indicate

there is room in the buffer to queue another transmit character if desired, and the SPI serial transfer starts.

During the SPI transfer, data is sampled (read) on the MISO pin at one SPSCK edge and shifted, changing

the bit value on the MOSI pin, one-half SPSCK cycle later. After eight SPSCK cycles, the data that was

in the shift register of the master has been shifted out the MOSI pin to the slave while eight bits of data

were shifted in the MISO pin into the master’s shift register. At the end of this transfer, the received data

byte is moved from the shifter into the receive data buffer and SPRF is set to indicate the data can be read

by reading SPID. If another byte of data is waiting in the transmit buffer at the end of a transfer, it is moved

into the shifter, SPTEF is set, and a new transfer is started.

Normally, SPI data is transferred most significant bit (MSB) first. If the least significant bit first enable

(LSBFE) bit is set, SPI data is shifted LSB first.

When the SPI is configured as a slave, its SS pin must be driven low before a transfer starts and SS must

stay low throughout the transfer. If a clock format where CPHA = 0 is selected, SS must be driven to a

logic 1 between successive transfers. If CPHA = 1, SS may remain low between successive transfers. See

Section 15.5.1, “SPI Clock Formats” for more details.

Because the transmitter and receiver are double buffered, a second byte, in addition to the byte currently

being shifted out, can be queued into the transmit data buffer, and a previously received character can be

in the receive data buffer while a new character is being shifted in. The SPTEF flag indicates when the

transmit buffer has room for a new character. The SPRF flag indicates when a received character is

available in the receive data buffer. The received character must be read out of the receive buffer (read

SPID) before the next transfer is finished or a receive overrun error results.

In the case of a receive overrun, the new data is lost because the receive buffer still held the previous

character and was not ready to accept the new data. There is no indication for such an overrun condition

so the application system designer must ensure that previous data has been read from the receive buffer

before a new transfer is initiated.

15.5.1

SPI Clock Formats

To accommodate a wide variety of synchronous serial peripherals from different manufacturers, the SPI

system has a clock polarity (CPOL) bit and a clock phase (CPHA) control bit to select one of four clock

formats for data transfers. CPOL selectively inserts an inverter in series with the clock. CPHA chooses

between two different clock phase relationships between the clock and data.

Figure 15-10 shows the clock formats when CPHA = 1. At the top of the figure, the eight bit times are

shown for reference with bit 1 starting at the first SPSCK edge and bit 8 ending one-half SPSCK cycle

after the sixteenth SPSCK edge. The MSB first and LSB first lines show the order of SPI data bits

depending on the setting in LSBFE. Both variations of SPSCK polarity are shown, but only one of these

waveforms applies for a specific transfer, depending on the value in CPOL. The SAMPLE IN waveform

applies to the MOSI input of a slave or the MISO input of a master. The MOSI waveform applies to the

HCS08 bảng dữ liệu(PDF) 230 Page - NXP Semiconductors

HCS08 bảng dữ liệu(HTML) 230 Page - NXP Semiconductors

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

bảng dữ liệu tải về

Link URL