công cụ tìm kiếm bảng dữ liệu linh kiện điện tử
  Vietnamese  ▼
ALLDATASHEET.VN

X  

TMP88CU74F bảng dữ liệu(PDF) 17 Page - Toshiba Semiconductor

tên linh kiện TMP88CU74F
Giải thích chi tiết về linh kiện  CMOS 8-BIT MICROCONTROLLER
PDF  132 Pages
Scroll/Zoom Zoom In 100%  Zoom Out
nhà sản xuất  TOSHIBA [Toshiba Semiconductor]
Trang chủ  http://www.semicon.toshiba.co.jp/eng
Logo TOSHIBA - Toshiba Semiconductor

TMP88CU74F bảng dữ liệu(HTML) 17 Page - Toshiba Semiconductor

Back Button TMP88CU74F Datasheet HTML 13Page - Toshiba Semiconductor TMP88CU74F Datasheet HTML 14Page - Toshiba Semiconductor TMP88CU74F Datasheet HTML 15Page - Toshiba Semiconductor TMP88CU74F Datasheet HTML 16Page - Toshiba Semiconductor TMP88CU74F Datasheet HTML 17Page - Toshiba Semiconductor TMP88CU74F Datasheet HTML 18Page - Toshiba Semiconductor TMP88CU74F Datasheet HTML 19Page - Toshiba Semiconductor TMP88CU74F Datasheet HTML 20Page - Toshiba Semiconductor TMP88CU74F Datasheet HTML 21Page - Toshiba Semiconductor Next Button
Zoom Inzoom in Zoom Outzoom out
 17 / 132 page
background image
TMP88CU74
2003-02-17
88CU74-17
3.
When the warming-up time has elapsed, normal operation resumes with the
instruction following the STOP mode start instruction (e.g. [SET (SYSCR1). 7]).
The start is made after the prescaler and the divider of the timing generator are
cleared to “0”.
Table 1.4.2 Warming-up Time Example (at fc
= 12.5 MHz, fs = 32.8 kHz)
Warming-up Time [ms]
Return to NORMAL mode
WUT
DV1CK
= 0
DV1CK
= 1
Return to SLOW mode
00
01
10
11
15.729
5.243
3.932
1.311
31.457
10.486
7.864
2.621
750
250
⎯
⎯
Note:
The warming-up time is obtained by dividing the basic clock by the divider: therefore, the
warming-up time may include a certain amount of error if there is any fluctuation of the
oscillation frequency when STOP mode is released. Thus, the warming-up time must be
considered an approximate value.
STOP mode can also be released by inputting low level on the RESET pin,
which immediately performs the normal reset operation.
Note:
When STOP mode is released with a low hold voltage, the following cautions must be
observed.
The power supply voltage must be at the operating voltage level before releasing STOP
mode. The RESET pin input must also be “H” level, rising together with the power supply
voltage. In this case, if an external time constant circuit has been connected, the RESET
pin input voltage will increase at a slower pace than the power supply voltage. At this time,
there is a danger that a reset may occur if input voltage level of the RESET pin drops below
the non-inverting high-level input voltage (hysteresis input).
2007-10-19



Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100  ...More


bảng dữ liệu tải về

Go To PDF Page


Link URL



Cho đến nay ALLDATASHEET có giúp ích cho doanh nghiệp của bạn hay không?  [ DONATE ] 

Alldatasheet là   |   Quảng cáo   |   Liên lạc với chúng tôi   |   Chính sách bảo mật   |   Liên kết đến bảng dữ liệu    |   Trao đổi link   |   Tìm kiếm theo nhà sản xuất
All Rights Reserved©Alldatasheet.com


Mirror Sites
English : Alldatasheet.com  |   English : Alldatasheet.net  |   Chinese : Alldatasheetcn.com  |   German : Alldatasheetde.com  |   Japanese : Alldatasheet.jp
Russian : Alldatasheetru.com  |   Korean : Alldatasheet.co.kr  |   Spanish : Alldatasheet.es  |   French : Alldatasheet.fr  |   Italian : Alldatasheetit.com
Portuguese : Alldatasheetpt.com  |   Polish : Alldatasheet.pl  |   Vietnamese : Alldatasheet.vn
Indian : Alldatasheet.in  |   Mexican : Alldatasheet.com.mx  |   British : Alldatasheet.co.uk  |   New Zealand : Alldatasheet.co.nz
Family Site : ic2ic.com  |   icmetro.com