| công cụ tìm kiếm bảng dữ liệu linh kiện điện tử |
|
98ASH70029A bảng dữ liệu(PDF) 13 Page - NXP Semiconductors |
|
|
|||||||||||||||||||||||||||||
98ASH70029A bảng dữ liệu(HTML) 13 Page - NXP Semiconductors |
|
13 / 60 page ![]() 2 MC56F826xx signal and pin descriptions After reset, each pin is configured for its primary function (listed first). Any alternative functionality, shown in parentheses, must be programmed through the GPIO module peripheral enable registers (GPIOx_PER) and the SIM module GPIO peripheral select (GPSx) registers. All GPIO ports can be individually programmed as an input or output (using bit manipulation). • PWMA_FAULT0, PWMA_FAULT1, and similar signals are inputs used to disable selected PWMA outputs, in cases where the fault conditions originate off-chip. For the MC56F826xx products, which use 48-pin LQFP and 32-pin packages: Table 2. Signal descriptions Signal Name 48 LQFP 32 LQFP Type State During Reset Signal Description VDD 32 — Supply Supply I/O Power — Supplies 3.3 V power to the chip I/O interface. 44 28 VSS 22 14 Supply Supply I/O Ground — Provide ground for the device I/O interface. 31 — 45 29 VDDA 15 9 Supply Supply Analog Power — Supplies 3.3 V power to the analog modules. It must be connected to a clean analog power supply. VSSA 16 10 Supply Supply Analog Ground — Supplies an analog ground to the analog modules. It must be connected to a clean power supply. VCAP 19 — On-chip regulator output On-chip regulator output Connect a 2.2 µF bypass capacitor between this pin and VSS to stabilize the core voltage regulator output required for proper device operation. NOTE: The total bypass capacitor value between all VCAP pin and VSS should not exceed 4.7 µF. 43 27 TDI 48 32 Input Input, internal pullup enabled Test Data Input — It is sampled on the rising edge of TCK and has an internal pullup resistor. After reset, the default state is TDI. (GPIOD0) Input/Output GPIO Port D0 TDO 46 30 Output Output Test Data Output — It is driven in the shift-IR and shift-DR controller states, and it changes on the falling edge of TCK. After reset, the default state is TDO (GPIOD1) Input/Output Output GPIO Port D1 TCK 1 1 Input Input, internal pulldown enabled Test Clock Input — The pin is connected internally to a pulldown resistor. A Schmitt- trigger input is used for noise immunity. After reset, the default state is TCK Table continues on the next page... MC56F826xx signal and pin descriptions MC56F826xx, Rev. 0, 08/2018 NXP Semiconductors 13 |
|
Link URL |
| Cho đến nay ALLDATASHEET có giúp ích cho doanh nghiệp của bạn hay không? [ DONATE ] |
Alldatasheet là | Quảng cáo | Liên lạc với chúng tôi | Chính sách bảo mật | Liên kết đến bảng dữ liệu | Trao đổi link | Tìm kiếm theo nhà sản xuất All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |