RM0352 datasheet(90/138 Pages) STMICROELECTRONICS

90 / 138 page

I2C bus interface

RM0352

90/138

DocID024647 Rev 1

1: master arbitration lost.

[23] SAL: slave arbitration lost (SMBUS mode). SAL is set when the slave loses

the arbitration during the data phase. A collision occurs when 2 devices

transmit simultaneously 2 opposite values on the serial dataline. The device

that is pulling up the line, identifies the collision reading a 0 value on the

sda_in signal, stops the transmission, releases the bus and waits for the idle

state (STOP condition received) on the bus line. The device which transmits

the first unique zero wins the bus arbitration. This interrupt is cleared setting

the related bit of the I2C_ICR register.

0: no slave arbitration lost.

1: slave arbitration lost.

[20] STD: slave transaction done. STD is set when a slave operation (write-to-

slave or read-from- slave) has been executed. The application shall read the

related transaction status (I2C_SR register), the pending data in the Rx FIFO

(only for a write-to-slave operation) and clear this interrupt (transaction

acknowledgment). A subsequent slave operation will be notified

(I2C_RISR:WTSR and I2C_RISR:RFSR interrupt bits assertion) after the

clearing of this interrupt, meanwhile the I

C clock line will be stretched low.

A subsequent master operation can be issued (writing the I2C_MCR register)

after the clearing of this interrupt. This interrupt is cleared setting the related

bit of the I2C_ICR register.

0: slave transaction acknowledged.

1: slave transaction done (ready for acknowledgment).

[19] MTD: master transaction done. MTD is set when a master operation (master

write or master read) has been executed after STOP condition. The

application shall read the related transaction status (I2C_SR register), the

pending data in the Rx FIFO (only for a master read operation) and clear this

interrupt (transaction acknowledgment). A subsequent master operation can

be issued (writing the I2C_MCR register) after the clearing of this interrupt.

A subsequent slave operation will be notified (I2C_RISR:WTSR and

I2C_RISR:RFSR interrupt bits assertion) after the clearing of this interrupt,

meanwhile the I

C clock line will be stretched low. This interrupt is cleared

setting the related bit of the I2C_ICR register.

0: master transaction acknowledged.

1: master transaction done (ready for acknowledgment).

[18] WTSR: write-to-slave request. WTSR is set when a write-to-slave operation

is received (I

C slave is addressed) from the I

C line. This interrupt is cleared

setting the related bit of the I2C_ICR register.

0: none write-to-slave request pending.

1: write-to-slave request is pending.

[17] RFSE: read-from-slave empty. RFSE is set when a read-from-slave operation

is in progress and the Tx FIFO is empty. On the assertion of this interrupt, the

CPU shall download in the Tx FIFO the data required for the slave operation.

This bit is self cleared writing in the Tx FIFO. At the end of the read-from-

slave operation this bit is cleared although the Tx FIFO is empty.

RM0352 bảng dữ liệu(PDF) 90 Page - STMicroelectronics

RM0352 bảng dữ liệu(HTML) 90 Page - STMicroelectronics

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

bảng dữ liệu tải về

Link URL