| công cụ tìm kiếm bảng dữ liệu linh kiện điện tử |
|
TMS570LS bảng dữ liệu(PDF) 68 Page - Texas Instruments |
|
|
|||||||||||||||||||||||||||||
TMS570LS bảng dữ liệu(HTML) 68 Page - Texas Instruments |
|
68 / 107 page ![]() OSCIN OSCOUT C1 (see Note A) C2 Crystal (a) (b) External (toggling 0-1.5V) Clock Signal Kelvin_GND (see Note B) OSCOUT OSCIN TMS570LS20206-EP, TMS570LS20216-EP SPNS209A – JUNE 2012 – REVISED AUGUST 2012 www.ti.com 7 Peripheral and Electrical Specifications 7.1 Clocks 7.1.1 PLL And Clock Specifications Table 7-1. Timing Requirements For PLL Circuits Enabled Or Disabled MIN MAX Unit f(OSC) (1) Input clock frequency 5 MHz f(OSC) Input clock frequency 20 MHz tc(OSC) Cycle time, OSCIN 50 ns tw(OSCIL) Pulse duration, OSCIN low 15 ns tw(OSCIH) Pulse duration, OSCIN high 15 ns f(OSCRST) (1) OSC FAIL frequency - upper level 20 50 MHz f(OSCRST) (1) OSC FAIL frequency - lower level 1.5 5 MHz (1) This parameter is characterized from -40°C to 125°C only. 7.1.2 External Reference Resonator/Crystal Oscillator Clock Option The oscillator is enabled by connecting the appropriate fundamental 5–20 MHz resonator/crystal and load capacitors across the external OSCIN and OSCOUT pins as shown in section (a) of the figure below. The oscillator is a single stage inverter held in bias by an integrated bias resistor. This resistor is disabled during leakage test measurement and HALT mode. NOTE TI strongly encourages each customer to submit samples of the device to the resonator/crystal vendors for validation. The vendors are equipped to determine what load capacitors will best tune their resonator/crystal to the microcontroller device for optimum start-up and operation over temperature/voltage extremes. An external oscillator source can be used by connecting a 1.5V clock signal to the OSCIN pin and leaving the OSCOUT pin unconnected (open) as shown in section (b) of the figure below. Figure 7-1. Recommended Crystal/Clock Connection NOTE In figure (a), The values of C1 and C2 should be provided by the resonator/crystal vendor. In figure (b), Kelvin_GND should not be connected to any other GND. 68 Peripheral and Electrical Specifications Copyright © 2012, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): TMS570LS20206-EP TMS570LS20216-EP |
|
Link URL |
| Cho đến nay ALLDATASHEET có giúp ích cho doanh nghiệp của bạn hay không? [ DONATE ] |
Alldatasheet là | Quảng cáo | Liên lạc với chúng tôi | Chính sách bảo mật | Liên kết đến bảng dữ liệu | Trao đổi link | Tìm kiếm theo nhà sản xuất All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |