AT90SCR100 datasheet(309/433 Pages) ATMEL

309 / 433 page

309

TPR0327AY–SMS–30Jan09

AT90SCR100

22.7.1

Master Transmitter Mode

In the Master Transmitter mode, a number of data bytes are transmitted to a Slave Receiver

(see Figure 22-11). In order to enter a Master mode, a START condition must be transmitted.

The format of the following address packet determines whether Master Transmitter or Master

Receiver mode is to be entered. If SLA+W is transmitted, MT mode is entered, if SLA+R is trans-

mitted, MR mode is entered. All the status codes mentioned in this section assume that the

prescaler bits are zero or are masked to zero.

Figure 22-11.

Data Transfer in Master Transmitter Mode

A START condition is sent by writing the following value to TWCR:

TWEN must be set to enable the 2-wire Serial Interface, TWSTA must be written to one to trans-

mit a START condition and TWINT must be written to one to clear the TWINT Flag. The TWI will

then test the 2-wire Serial Bus and generate a START condition as soon as the bus becomes

free. After a START condition has been transmitted, the TWINT Flag is set by hardware, and the

status code in TWSR will be 0x08 (see Table 22-2). In order to enter MT mode, SLA+W must be

transmitted. This is done by writing SLA+W to TWDR. Thereafter the TWINT bit should be

cleared (by writing it to one) to continue the transfer. This is accomplished by writing the follow-

ing value to TWCR:

When SLA+W have been transmitted and an acknowledgement bit has been received, TWINT is

set again and a number of status codes in TWSR are possible. Possible status codes in Master

mode are 0x18, 0x20, or 0x38. The appropriate action to be taken for each of these status codes

is detailed in Table 22-2.

When SLA+W has been successfully transmitted, a data packet should be transmitted. This is

done by writing the data byte to TWDR. TWDR must only be written when TWINT is high. If not,

Please note that R1 and R2 resistors may not be required. The internal pull-up

resistors on SDA and SCL pads of AVR may be sufficient to setup a communica-

tion. However, if the edges are not strong enough to get a clean signals, R1 and

R2 can be added.

TWCR

TWINT

TWEA

TWSTA

TWSTO

TWWC

TWEN

–

TWIE

value

TWCR

TWINT

TWEA

TWSTA

TWSTO

TWWC

TWEN

–

TWIE

value

Device 1

MASTER

TRANSMITTER

Device 2

SLAVE

RECEIVER

Device 3

Device n

SDA

SCL

........

Note

AT90SCR100 bảng dữ liệu(PDF) 309 Page - ATMEL Corporation

AT90SCR100 bảng dữ liệu(HTML) 309 Page - ATMEL Corporation

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

bảng dữ liệu tải về

Link URL