AT90SCR100 datasheet(94/433 Pages) ATMEL

94 / 433 page

TPR0327AY–SMS–30Jan09

AT90SCR100

the pin is set to output. The waveform generated will have a maximum frequency of fOC0 =

fclk_I/O/2 when OCR0A is set to zero (0x00). The waveform frequency is defined by the following

equation:

The N variable represents the prescale factor (1, 8, 64, 256, or 1024).

As for the Normal mode of operation, the TOV0 Flag is set in the same timer clock cycle that the

counter counts from MAX to 0x00.

13.1.7.3

Fast PWM Mode

The fast Pulse Width Modulation or fast PWM mode (WGM02:0 = 3 or 7) provides a high fre-

quency PWM waveform generation option. The fast PWM differs from the other PWM option by

its single-slope operation. The counter counts from BOTTOM to TOP then restarts from BOT-

TOM. TOP is defined as 0xFF when WGM2:0 = 3, and OCR0A when WGM2:0 = 7. In non-

inverting Compare Output mode, the Output Compare (OC0x) is cleared on the Compare Match

between TCNT0 and OCR0x, and set at BOTTOM. In inverting Compare Output mode, the out-

put is set on Compare Match and cleared at BOTTOM. Due to the single-slope operation, the

operating frequency of the fast PWM mode can be twice as high as the phase correct PWM

mode that use dual-slope operation. This high frequency makes the fast PWM mode well suited

for power regulation, rectification, and DAC applications. High frequency allows physically small

sized external components (coils, capacitors), and therefore reduces total system cost.

In fast PWM mode, the counter is incremented until the counter value matches the TOP value.

The counter is then cleared at the following timer clock cycle. The timing diagram for the fast

PWM mode is shown in Figure 13-6. The TCNT0 value is in the timing diagram shown as a his-

togram for illustrating the single-slope operation. The diagram includes non-inverted and

inverted PWM outputs. The small horizontal line marks on the TCNT0 slopes represent Com-

pare Matches between OCR0x and TCNT0.

Figure 13-6.

Fast PWM Mode, Timing Diagram

The Timer/Counter Overflow Flag (TOV0) is set each time the counter reaches TOP. If the inter-

rupt is enabled, the interrupt handler routine can be used for updating the compare value.

OC nx

fclk_I/O

2 N

1 OCRnx

()

⋅⋅

--------------------------------------------------

TCNT0

OCR0x Update and

TOV0 Interrupt Flag Set

Period

OC0x

(COM0x1:0 = 2)

(COM0x1:0 = 3)

OCR0x Interrupt Flag Set

AT90SCR100 bảng dữ liệu(PDF) 94 Page - ATMEL Corporation

AT90SCR100 bảng dữ liệu(HTML) 94 Page - ATMEL Corporation

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

bảng dữ liệu tải về

Link URL