| công cụ tìm kiếm bảng dữ liệu linh kiện điện tử |
|
PTPS7H4102PAPTSEP bảng dữ liệu(PDF) 39 Page - Texas Instruments |
|
|
|||||||||||||||||||||||||||||
PTPS7H4102PAPTSEP bảng dữ liệu(HTML) 39 Page - Texas Instruments |
|
39 / 76 page ![]() 8.3.5 Power Good (PWRGDx) The PWRGDx pin is an open-drain output that is asserted when the output voltage (VOUTx) reaches an appropriate range. This is achieved by comparing the voltage at the VSNSx pin with the internal reference voltage (VREFx). The PWRGDx pins are externally pulled-up through a resistor to a voltage source with the desired logic level (typically VOUTx). The maximum voltage the PWRGDx pins can be pulled-up is 7V. Select the pull-up resistor value to keep the maximum current sink by PWRGDx to under the recommended operating condition current maximum of 2mA. Generally a pull up resistor of 10kΩ is sufficient. Using a larger value resistor minimizes power dissipation but can allow switching noise to couple into the PWRGDx signal due a "weaker" pull-up. The PWRGDx signals logical states are: 1. Asserted (high impedance or logic high): when the VOUTx voltage in percent of final (nominal) value is: • Between 92% to 96% during a rising voltage (from an under-voltage or power-up condition). • Between 104% to 108% during a falling voltage (from an over-voltage condition). 2. Deasserted (low impedance or logic low) when the VOUTx voltage in percent of final (nominal) value is: • Between 89% to 92% during a falling voltage (or an under-voltage condition). • Between 107% to 111% during a rising voltage (or over-voltage condition). The responses of PWRGDx to the UV_GOOD and UV_FAULT are shown in Figure 8-4, while the OV_FAULT and OV_GOOD is presented on Figure 8-5. The PWRGDx is in a defined state when the VIN input voltage is greater than 1V but has reduced current sinking capability (See Figure 8-6). The PWRGD achieves full current sinking capability by the time VIN reaches 3V. For more details on the VINMIN_PWRGDx refer to POWER GOOD section in Section 6.5. In addition to the description of PWRGDx above, PWRGDx is deasserted (forced low) during other conditions that cause regulation to stop such as: • VIN UVLO. • PVIN UVLO • The device is in thermal shutdown. • The device ENx pin is logic low (or disabled). • The COMPx pin reaches the COMPxCLAMP threshold voltage (1.9V typical). – COMPxCLAMP force a re-start of VOUTx VREFx VOUTx_NOMINAL 0 V 0 V PWRGDxUV_GOOD × VREFx 0 V PWRGDxUV_FAULT× VREFx VPWRGDx_PULL_UP me me me VPWRGDx_VOL A. In this plot is assumed that VIN is in a valid range between 3V to 7V, and a valid rising edge (↑) voltage is provided in the ENx. Figure 8-4. PWRGDx Undervoltage (UV) Tresholds www.ti.com TPS7H4104-SEP, TPS7H4102-SEP SLVSH61B – MARCH 2025 – REVISED SEPTEMBER 2025 Copyright © 2025 Texas Instruments Incorporated Submit Document Feedback 39 Product Folder Links: TPS7H4104-SEP TPS7H4102-SEP |
|
Link URL |
| Cho đến nay ALLDATASHEET có giúp ích cho doanh nghiệp của bạn hay không? [ DONATE ] |
Alldatasheet là | Quảng cáo | Liên lạc với chúng tôi | Chính sách bảo mật | Liên kết đến bảng dữ liệu | Trao đổi link | Tìm kiếm theo nhà sản xuất All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |