| công cụ tìm kiếm bảng dữ liệu linh kiện điện tử |
|
6402 bảng dữ liệu(PDF) 236 Page - Intel Corporation |
|
|
|||||||||||||||||||||||||||||
6402 bảng dữ liệu(HTML) 236 Page - Intel Corporation |
|
236 / 250 page ![]() Registers 236 Intel® 6400/6402 Advanced Memory Buffer Datasheet 14.8.2.12 SBIBISTMISC: SB Intel IBIST Initialization Miscellaneous Register This register control southbound Intel IBIST Testing. 14.8.3 Northbound FBD Intel IBIST Registers 14.8.3.1 NBFIBPORTCTL: Northbound FBD Intel IBIST Port Control Register This register controls the operation of the Intel IBIST logic. Device: NodeID Function: 6 Offset: B4h Bit Attr Default Description 31: RV 00h Reserved 23:20 RWST 0h AMBID: Value of the AMB ID field during TS0 19:0 RWST 61a80h SBIBISTCALPERIOD: Number of cycles to drive 1 during Calibration Device: NodeID Function: 6 Offset: C0h Bit Attr Default Description 31:24 RV 00h Reserved 23 RWST 0 SBNBMAP: Loopback mapping bit This bit will be sent during TS1 to specify to the slave which lanes needs to be looped back. Actual lanes looped back is specified in the FBD Architecture Spec. 22 RWST 0 CMMSTR: Compliance Measurement Mode start This puts the Intel IBIST logic in CMM mode and Intel IBIST TX engine will start transmitting Intel IBIST patterns. 21:12 RWCST 000h ERRCNT: Error Counter Total number of frames with errors that were encountered by this port. 11:8 ROST 0h ERRLNNUM: Error Lane Number This points to the first lane that encountered an error. If more than one lane reports an error in a cycle, the most significant lane number that reported the error will be logged. 7:6 RWCST 00 ERRSTAT: Port Error Status When Intel IBIST is started, status goes to 01 until first start delimiter is received and then goes to 00 until the end or to10 if an error occurs. 00: No error. 01: Did not receive first start delimiter. 10: Transmission error (first error). 11: Reserved 5RWST 0 AUTOINVSWPEN: Auto Inversion sweep enable This bit enables the inversion shift register to continuously rotate the pattern in the FIBTXSHFT and FIBRXSHFT registers. 0: Disable Auto-inversion 1: Enable Auto-inversions 4RWST 0 STOPONERR: Stop IBIST on Error 0: Do not stop on error, only update error counter 1: Stop on error 3RWST 0 LOOPCON: Loop forever 0: No looping 1: Loop forever |
|
Link URL |
| Cho đến nay ALLDATASHEET có giúp ích cho doanh nghiệp của bạn hay không? [ DONATE ] |
Alldatasheet là | Quảng cáo | Liên lạc với chúng tôi | Chính sách bảo mật | Liên kết đến bảng dữ liệu | Trao đổi link | Tìm kiếm theo nhà sản xuất All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |