TMPR4925 datasheet(238/590 Pages) TOSHIBA

238 / 590 page

Chapter 9 SDRAM Controller

9-10

9.3.4

Low Power Consumption Function

9.3.4.1

Power Down Mode, Self-Refresh Mode, Deep Power Down Mode

SDRAM has two low power consumption modes called the Power Down mode and the Self-

Refresh mode. Memory data is lost in the case of the Power Down mode since Memory Refresh is

not performed, but the amount of power consumed is reduced the most. Memory data is not lost in

the case of the Self-Refresh mode.

SDRAM is set to the Power Down mode by using the SDRAM Command Register (SDCCMD)

to issue the Power Down Mode command. Similarly, SDRAM is set to the Self-Refresh mode by

issuing the Self-Refresh Mode command. The SDRAMC terminates internal refresh circuit

operation after one of these commands has been issued. Issuing the Normal Mode command

returns operation to normal.

When the Power Down Auto Entry bit (SDCTR.PDAE) of the SDRAM Timing Register is set,

SDRAM is automatically set to the Power Down mode when memory access is not being

performed. The SDRAMC internal refresh circuit will continue operating, so there will be no loss

of memory data.

If either the Memory Access, Memory Refresh, or Memory command is executed while

SDRAM is set to the Power Down mode or the Self-Refresh mode, then the Power Down mode

and Self-Refresh mode will automatically terminate, and memory access will be performed.

After returning from a low power consumption mode that was set by either the Power Down

Mode command or the Self-Refresh Mode command, the next memory access starts after 10

SDCLK cycles pass. This latency sufficiently follows the stipulated time from Power Down to

first access of the SDRAM.

If setting the Power Down Auto Entry bit automatically causes memory access to be requested

when set in the Power Down mode, then add 1 SDCLK cycle more of access latency than when

not in the Power Down mode.

SyncFlash has two low power consumption modes called the Power Down mode and the Deep

Power Down mode. Memory data is not lost in both mode. SyncFlash need the device power-up

initialize sequence in the case of the Deep Power Down mode, but the amount of power consumed

is reduced the most.

9.3.4.2

Advanced CKE

Advanced CKE is a function that speeds up the CKE assertion and deassertion timing by 1

clock cycle. This function is set using the Address CKE bit (SDCTR.ACE) of the SDRAM Timing

Advanced CKE assumes that it will be used in a system where SDRAM data is saved even

when the power to the TX4925 itself is cut. Since CKE On/Off becomes 1 cycle faster, it is

possible to delay CKE by 1 clock cycle using external power consumption control logic. Please set

the SDRAM to the Self-Refresh mode before using this function.

When combining advanced CKE functionality with Power Down Auto Entry functionality and

memory access is requested while in the Power Down mode, two more SDCLK cycles of latency

are added than would be the case when not in the Power Down mode.

TMPR4925 bảng dữ liệu(PDF) 238 Page - Toshiba Semiconductor

TMPR4925 bảng dữ liệu(HTML) 238 Page - Toshiba Semiconductor

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

bảng dữ liệu tải về

Link URL