TMPR4925 datasheet(68/590 Pages) TOSHIBA

68 / 590 page

Chapter 3 Signals

3-10

Table 3.1.14 Extended EJTAG Interface Signals (2/2)

Signal Name

Type

Description

Initial State

TPC[3:1]

Output

PC Trace Output

TPC[3:1] output the value of the noncontiguous program counter in sync with DCLK.

The pins are shared with other functions (refer to Section "3.3 Pin Multiplexing").

Selected by

TDO

H: PIO input

L: All High

TMS

Input

JTAG Test Mode Select Input

TMS mainly controls state transition in the TAP controller state machine.

Input

TRST*

Input

Test Reset Input

Asynchronous reset input for the TAP controller and debug support unit (DSU).

When an EJTAG probe is not connected, this pin must be fixed to low. When

connecting an EJTAG probe, prevent floating, for example, by connecting a pull-up

resistor. When this signal is deasserted, G-Bus timeout detection is disabled (refer to

Section “5.1.1 Detecting G-Bus Timeout”).

Input

DCLK

Output

Debug Clock

Clock output signal for the real-time debugging system.

When PC trace mode is selected, the TPC[3:1] and PCST signals are output

synchronously. This clock is the TX49/H2 core operating clock (CPUCLK) divided by

The pin is shared with other functions (refer to Section "3.3 Pin Multiplexing").

Selected by

TDO

H: PIO input

L: Low

PCST[8:0]

Output

PC Trace Status Information

Outputs PC trace status and other information.

The pins are shared with other functions (refer to Section "3.3 Pin Multiplexing").

Selected by

TDO

H: PIO input

(PCST[8:1])

BC32K(PC

ST[0])

L: All Low

3.1.15

Clock Signals

Table 3.1.15 Clock Signals

Signal Name

Type

Description

Initial State

MASTERCLK

Input

Master Clock

Input pin for the TX4925 operating clock. A crystal resonator cannot be connected to

this pin because the pin does not contain an oscillator.

Input

C32KIN

Input

32 KHz Crystal Input

Connect this pin and C32KOUT to a 32.768 kHz crystal.

Input

C32KOUT

Output

32 KHz Crystal output

Connect this pin and C32KIN to a 32.768 kHz crystal.

Output

BC32K

Output

Buffer output of 32 KHz Crystal

Buffer output for a 32.768 kHz clock.

Selected by

TDO

H: Output

(BC32K)

L: Low

3.1.16

Initialization Signals

Table 3.1.16 Initialization Signals

Signal Name

Type

Description

Initial State

RESET*

Input

SMT

Reset

Reset signal.

Input

PON*

Input

SMT

Power On Reset

Initializes the CG. For timing, refer to Section "6.3 Power-On Sequence".

Input

TMPR4925 bảng dữ liệu(PDF) 68 Page - Toshiba Semiconductor

TMPR4925 bảng dữ liệu(HTML) 68 Page - Toshiba Semiconductor

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

bảng dữ liệu tải về

Link URL