| công cụ tìm kiếm bảng dữ liệu linh kiện điện tử |
|
TMPR4925 bảng dữ liệu(PDF) 301 Page - Toshiba Semiconductor |
|
|
|||||||||||||||||||||||||||||
TMPR4925 bảng dữ liệu(HTML) 301 Page - Toshiba Semiconductor |
|
301 / 590 page ![]() Chapter 10 PCI Controller 10-39 Bits Mnemonic Field Name Description 5 G2PM2EN Initiator Memory Space 2 Enable Initiator Memory Space 2 Enable (Initial value: Normal Mode: 0; PCI Boot Mode: 1, R/W) Controls PCI initiator access to Memory Space 2. 1: Memory Space 2 is valid. 0: Memory Space 2 is invalid. 4G2PIOEN Initiator I/O Space Enable Initiator I/O Space Enable (Initial value: 0, R/W) Controls PCI initiator access to the I/O Space.. 1: I/O Space is valid. 0: I/O Space is invalid. 3 IRBER Bus Error Response Setting During Initiator Access Initiator Access Bus Error Response (Initial value: 1, R/W) Bus error responses on the G-Bus are controlled when the following phenomena indicated by the PCI Status, Command Register (PICSTATUS) and the G2P Status Register (G2PSTATUS) occur during initiator Read access. Detected Fatal Error (G2PSTATUS.MDFE) Detected Parity Error (G2PSTATUS.MDPE) Received Master Abort (PCISTATUS.RMA) Received Target Abort (PCISTATUS.RTA) Initiator Detected TRDY Time Out Error (G2PSTATUS.IDTTOE) Initiator Detected Retry Time Out Error (G2PSTATUS.IDRTOE) 1: Responds with a Bus error on the G-Bus. 0: Does not respond with a Bus error on the G-Bus. (Normally terminates the transaction on the G-Bus. Read data is invalid.) 2 Reserved 1 BSWAPI Byte Swap for Indirect, Config, IACK, and Special cycle Byte Swap for Indirect, Config, IACK, and Special cycle (Initial value: Little Endian Mode: 0; Big Endian Mode: 1, R/W) Sets the byte swapping of Indirect, Config, IACK, and Special cycle. 0: Do not perform byte swapping. 1: Perform byte swapping. Please use the default state in most situations. If this bit is changed to “0” when in the Big Endian Mode, the byte order of transfer to Memory Space 0 through DWORD (32- bit) access will not change. 0 ASERR Assert SERR Assert SERR (Initial value: 0, R/W1C) A write of 1 will assert SERR for 1 PCI clock. Always read 0. Figure 10.4.13 G2P Configuration Register (2/2) |
|
Link URL |
| Cho đến nay ALLDATASHEET có giúp ích cho doanh nghiệp của bạn hay không? [ DONATE ] |
Alldatasheet là | Quảng cáo | Liên lạc với chúng tôi | Chính sách bảo mật | Liên kết đến bảng dữ liệu | Trao đổi link | Tìm kiếm theo nhà sản xuất All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |