MCIMX503CVM8B datasheet(33/136 Pages) NXP

33 / 136 page

Electrical Characteristics

i.MX50 Applications Processors for Consumer Products, Rev. 7

Freescale Semiconductor

4.3.2

DDR2 I/O DC Parameters

The DDR2 interface fully complies with JESD79-2E DDR2 JEDEC standard release April, 2008. The

JEDEC LPDDR2 specification (JESD209_2B) supersedes any specification in this document. The

parameters in Table 19 are guaranteed per the operating ranges in Table 11, unless otherwise noted.

Input current (100 K

Ω PD)

IIN

VI = 0

VI=OVDD

——

0.25

μA

External pull-up / pull-down

resistor required to overdrive

internal keeper

Rext

—

1 To maintain a valid level, the transitioning edge of the input must sustain a constant slew rate (monotonic) from the current DC

level through to the target DC level, VIL or VIH. Monotonic input transition time is from 0.1ns to 1s. VIL and VIH do not apply

when hysteresis is enabled.

2 Hysteresis of 250 mV is guaranteed overall operating conditions when hysteresis is enabled.

Table 19. DDR2 DC Electrical Characteristics

DC Electrical Characteristics

Symbol

Test

Conditions

MIN

TYP

MAX

Units

High-level output voltage

Voh

—

0.9*ovdd

—

Low-level output voltage

Vol

—

0.1*ovdd

Output min source current1

1 ovdd=1.7 V; Vout=1.42 V. (Vout-ovdd)/Ioh must be less than 21 Ω for values of Vout between ovdd and ovdd-0.28 V.

Ioh(dc)

—

-7.5

—

Output min sink current2

2 ovdd=1.7 V; Vout=280 mV. Vout/Iol must be less than 21 Ω for values of Vout between 0 V and 280 mV.

Iol(dc)

—

7.5

—

Input reference voltage

Vref

—

0.49*ovdd

0.5*ovdd

0.51*ovdd

—

DC input high voltage (data pins)

Vihd(dc)

—

Vref+0.125

—

ovdd+0.3

DC input low voltage (data pins)

Vild(dc)

—

-0.3

—

Vref-0.125

DC input voltage3 (clk pins)

3 Vin(dc) specifies the allowable dc excursion of each differential input.

Vin(dc)

—

-0.3

—

ovdd+0.3

DC differential input voltage4

4 Vid(dc) specifies the input differential voltage |Vtr-Vcp| required for switching, where Vtr is the “pure” input level and Vcp is the

“complementary” input level. the minimum value is equal to Vih(dc) - Vil(dc).

Vid(dc)

—

0.25

—

ovdd+0.6

Termination voltage5

5 Vtt is expected to track ovdd/2.

Vtt

—

Vref-0.04

Vref

Vref+0.04

—

Input current6 (no pull-up/down)

6 Typ condition: typ model, 1.8 V, and 25 °C. Max condition: BCS model, 1.9 V, and 125 °C. Min condition: WCS model, 1.7 V,

and -40 °C.

Iin

VI = 0

VI=ovdd

—0.07

360

Tri-state I/O supply current6

Icc-ovdd

VI = ovdd or 0

—

2.3

480

Tri-state 2.5V predrivers supply

current6

Icc-vdd2p5

VI = ovdd or 0

—

6.4

750

Tri-state core supply current6

Icc-vddi

VI = ovdd or 0

—

3.1

720

Table 18. GPIO DC Electrical Characteristics (continued)

DC Electrical Characteristics

Symbol

Test Conditions

MIN

Typ

MAX

Units

MCIMX503CVM8B bảng dữ liệu(PDF) 33 Page - NXP Semiconductors

MCIMX503CVM8B bảng dữ liệu(HTML) 33 Page - NXP Semiconductors

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

bảng dữ liệu tải về

Link URL