PMS232 datasheet(37/94 Pages) PADAUK

37 / 94 page

PMC232/PMS232 Series

12-bit ADC Enhanced FPPA

8-bit OTP Controller

Page 37 of 94

PDK-DS-PMx232_V104– Dec. 18, 2018

Usually, .ADJUST_IC will be the first command after boot up, in order to set the target operating frequency

whenever starting the system. The program code for IHRC frequency calibration is executed only one time

that occurs in writing the codes into OTP memory; after then, it will not be executed again. If the different

option for IHRC calibration is chosen, the system status is also different after boot. The following shows the

status of PMC232/PMS232 for different option:

(1) .ADJUST_IC

SYSCLK=IHRC/2, IHRC=16MHz, VDD=5V, Band-gap=On

After boot up, CLKMD = 0x34：

 IHRC frequency is calibrated to 16MHz@VDD=5V and IHRC module is enabled

 System CLK = IHRC/2 = 8MHz

 Watchdog timer is disabled, ILRC is enabled, PA5 is in input mode, BG=1.2V

(2) .ADJUST_IC

SYSCLK=IHRC/4, IHRC=16MHz, VDD=3.3V, Band-gap=On

After boot up, CLKMD = 0x14：

 IHRC frequency is calibrated to 16MHz@VDD=3.3V and IHRC module is enabled

 System CLK = IHRC/4 = 4MHz

 Watchdog timer is disabled, ILRC is enabled, PA5 is in input mode, BG=1.2V

(3) .ADJUST_IC

SYSCLK=IHRC/8, IHRC=16MHz, VDD=2.5V, Band-gap=On

After boot up, CLKMD = 0x3C：

 IHRC frequency is calibrated to 16MHz@VDD=2.5V and IHRC module is enabled

 System CLK = IHRC/8 = 2MHz

 Watchdog timer is disabled, ILRC is enabled, PA5 is in input mode, BG=1.2V

(4) .ADJUST_IC

SYSCLK=IHRC/16, IHRC=16MHz, VDD=2.5V, Band-gap=On

After boot up, CLKMD = 0x1C：

 IHRC frequency is calibrated to 16MHz@VDD=2.5V and IHRC module is enabled

 System CLK = IHRC/16 = 1MHz

 Watchdog timer is disabled, ILRC is enabled, PA5 is in input mode, BG=1.2V

(5) .ADJUST_IC

SYSCLK=IHRC/32, IHRC=16MHz, VDD=5V, Band-gap=Off

After boot up, CLKMD = 0x7C：

 IHRC frequency is calibrated to 16MHz@VDD=5V and IHRC module is enabled

 System CLK = IHRC/32 = 500kHz

 Watchdog timer is disabled, ILRC is enabled, PA5 is in input mode

(6) .ADJUST_IC

SYSCLK=ILRC, IHRC=16MHz, VDD=5V, Band-gap=Off

After boot up, CLKMD = 0XE4：

 IHRC frequency is calibrated to 16MHz@VDD=5V and IHRC module is disabled

 System CLK = ILRC

 Watchdog timer is disabled, ILRC is enabled, PA5 is input mode

(7) .ADJUST_IC

DISABLE

After boot up, CLKMD is not changed (Do nothing)：

 IHRC is not calibrated and IHRC module is disabled, Band-gap is not calibrated

 System CLK = ILRC

 Watchdog timer is enabled, ILRC is enabled, PA5 is in input mode,

PMS232 bảng dữ liệu(PDF) 37 Page - PADAUK Technology.

PMS232 bảng dữ liệu(HTML) 37 Page - PADAUK Technology.

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94

bảng dữ liệu tải về

Link URL