| công cụ tìm kiếm bảng dữ liệu linh kiện điện tử |
|
M37271MF-252SP bảng dữ liệu(PDF) 74 Page - Mitsubishi Electric Semiconductor |
|
|
|||||||||||||||||||||||||||||
M37271MF-252SP bảng dữ liệu(HTML) 74 Page - Mitsubishi Electric Semiconductor |
|
74 / 97 page ![]() MITSUBISHI MICROCOMPUTERS M37271MF-XXXSP M37271EF-XXXSP, M37271EFSP SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER with CLOSED CAPTION DECODER and ON-SCREEN DISPLAY CONTROLLER 74 (15) OSD Output Pin Control The OSD output pins R, G, B, and OUT1 can also function as ports P52, P53, P54 and P55. Set the corresponding bit of the OSD port control register (address 00CB16) to “0” to specify these pins as OSD output pins, or set it to “1” to specify it as a general-purpose port P5 pins. The OUT2, I1, and I2 can also function as port P10, P15, P16. Set the corresponding bit of the port P1 direction register (address 00C316) to “1” (output mode). After that, switch between the OSD output function and the port function by the OSD port control regis- ter. Set the corresponding bit to “1” to specify the pin as OSD output pin, or set it to “0” to specify as port P1 pin. The input polarity of the HSYNC, VSYNC and output polarity of signals R, G, B, I1, I2, OUT1 and OUT2 can be specified with the I/O polarity control register (address 021716) . Set a bit to “0” to specify positive polarity; set it to “1” to specify negative polarity (refer to Figure 64). The structure of the OSD port control register is shown in Figure 83. Fig. 83. Structure of OSD port control register 70 0 OSD port control register (PF : address 00CB16) Port P15 output signal selection bit 0 : Port P15 output 1 : I1 signal output Port P16 output signal selection bit 0 : Port P16 output 1 : I2 signal output Port P52 output signal selection bit 0 : R signal output 1 : Port P52 output Port P53 output signal selection bit 0 : G signal output 1 : Port P53 output Port P54 output signal selection bit 0 : B signal output 1 : Port P54 output Port P55 output signal selection bit 0 : OUT1 signal output 1 : Port P55 output Port P10 output signal selection bit 0 : Port P10 output 1 : OUT2 signal output Fix this bit to “0.” |
|
Link URL |
| Cho đến nay ALLDATASHEET có giúp ích cho doanh nghiệp của bạn hay không? [ DONATE ] |
Alldatasheet là | Quảng cáo | Liên lạc với chúng tôi | Chính sách bảo mật | Liên kết đến bảng dữ liệu | Trao đổi link | Tìm kiếm theo nhà sản xuất All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |