| công cụ tìm kiếm bảng dữ liệu linh kiện điện tử |
|
HCS08 bảng dữ liệu(PDF) 177 Page - NXP Semiconductors |
|
|
|||||||||||||||||||||||||||||
HCS08 bảng dữ liệu(HTML) 177 Page - NXP Semiconductors |
|
177 / 198 page ![]() Appendix A Electrical Characteristics MC9S08QD4 Series MCU Data Sheet, Rev. 6 Freescale Semiconductor 177 High impedance (off-state) leakage current (per pin) VIn = VDD or VSS, all input/output |IOZ| — 0.025 1.0 μA Internal pullup resistors4 RPU 17.5 52.5 k Ω Internal pulldown resistor (IRQ) RPD 17.5 52.5 k Ω Output high voltage — Low Drive (PTxDSn = 0) 5 V, ILoad = –2 mA 3 V, ILoad = –0.6 mA 5 V, ILoad = –0.4 mA 3 V, ILoad = –0.24 mA VOH VDD – 1.5 VDD – 1.5 VDD – 0.8 VDD – 0.8 — — — — — — — — V Output high voltage — High Drive (PTxDSn = 1) 5 V, ILoad = –10 mA 3 V, ILoad = –3 mA 5 V, ILoad = –2 mA 3 V, ILoad = –0.4 mA VDD – 1.5 VDD – 1.5 VDD – 0.8 VDD – 0.8 — — — — — — — — Maximum total IOH for all port pins 5V 3V |IOHT| — — — — 100 60 mA Output low voltage — Low Drive (PTxDSn = 0) 5 V, ILoad = 2 mA 3 V, ILoad = 0.6 mA 5 V, ILoad = 0.4 mA 3 V, ILoad = 0.24 mA VOL — — — — — — — — 1.5 1.5 0.8 0.8 V Output low voltage — High Drive (PTxDSn = 1) 5 V, ILoad = 10 mA 3 V, ILoad = 3 mA 5 V, ILoad = 2 mA 3 V, ILoad = 0.4 mA — — — — — — — — 1.5 1.5 0.8 0.8 Maximum total IOL for all port pins 5V 3V IOLT — — — — 100 60 mA DC injection current2, 5, 6, 7 Single pin limit VIN > VDD VIN < VSS Total MCU limit, includes sum of all stressed pins VIN > VDD VIN < VSS IIC 0 0 0 0 — 2 –0.2 12 –1.2 mA Input capacitance (all non-supply pins) CIn —7 pF 1 Maximum is highest voltage that POR is guaranteed. 2 RAM will retain data down to POR voltage. RAM data not guaranteed to be valid following a POR. 3 This parameter is characterized and not tested on each device. 4 Measurement condition for pull resistors: V In = VSS for pullup and VIn = VDD for pulldown. 5 All functional non-supply pins are internally clamped to V SS and VDD. 6 Input must be current limited to the value specified. To determine the value of the required current-limiting resistor, calculate resistance values for positive and negative clamp voltages, then use the larger of the two values. Table A-5. DC Characteristics (continued)(Temperature Range = –40 to 125 °C Ambient) Parameter Symbol Min Typical Max Unit |
|
Link URL |
| Cho đến nay ALLDATASHEET có giúp ích cho doanh nghiệp của bạn hay không? [ DONATE ] |
Alldatasheet là | Quảng cáo | Liên lạc với chúng tôi | Chính sách bảo mật | Liên kết đến bảng dữ liệu | Trao đổi link | Tìm kiếm theo nhà sản xuất All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |