| công cụ tìm kiếm bảng dữ liệu linh kiện điện tử |
|
DSP56307/D bảng dữ liệu(PDF) 40 Page - Motorola, Inc |
|
|
|||||||||||||||||||||||||||||
DSP56307/D bảng dữ liệu(HTML) 40 Page - Motorola, Inc |
|
40 / 156 page ![]() 2-4 DSP56307 Technical Data MOTOROLA Specifications AC Electrical Characteristics AC ELECTRICAL CHARACTERISTICS The timing waveforms shown in the ac electrical characteristics section are tested with a VIL maximum of 0.3 V and a VIH minimum of 2.4 V for all pins except EXTAL, which is tested using the input levels shown in Note 6 of Table 2-3. AC timing specifications, which are referenced to a device input signal, are measured in production with respect to the 50 percent point of the respective input signalÕs transition. DSP56307 output levels are measured with the production test machine VOL and VOH reference levels set at 0.8 V and 2.0 V, respectively. INTERNAL CLOCKS Notes: 1. VCCQL/VCCP = 2.5 V ± 0.2 V; I/O VCC = 3.3 ± 0.3 V; TJ = Ð40ûC to +100 ûC, CL = 50 pF 2. Refers to MODA/IRQA, MODB/IRQB, MODC/IRQC, and MODD/IRQD pins 3. Driving EXTAL to the low VIHX or the high VILX value may cause additional power consumption (dc current). To minimize power consumption, the minimum VIHX should be no lower than 0.9 × V CC and the maximum VILX should be no higher than 0.1 × VCC. 4. Periodically sampled and not 100% tested 5. This characteristic does not apply to XTAL and PCAP. 6. Power Consumption Considerations on page SECTION 4-4 provides a formula to compute the estimated current requirements in Normal mode. In order to obtain these results, all inputs must be terminated (i.e., not allowed to float). Measurements are based on synthetic intensive DSP benchmarks. (For an example, see Appendix A, Power Consumption Benchmark on page APPENDIX A-1.) The power consumption numbers in this specification are 90% of the measured results of this benchmark. This reflects typical DSP applications. Typical internal supply current is measured with VCCQL = 2.5 V at TJ = 100ûC. Maximum internal supply current may vary widely and is application dependent. 7. In order to obtain these results, all inputs must be terminated (i.e., not allowed to float). PLL and XTAL signals are disabled during Stop state. 8. In order to obtain these results, all inputs not disconnected in Stop mode must be terminated (i.e., not allowed to float). 9. See DSP56307 Errata ES 74. for appropriate operating voltages for appropriate mask sets. 10. See DSP56307 Errata ES93 for appropriate workarounds to data bus drift problem. Table 2-4 Internal Clocks, CLKOUT Characteristics Symbol Expression1, 2 Min Typ Max Internal operation frequency and CLKOUT with PLL enabled f Ñ (Ef × MF)/ (PDF × DF) Ñ Table 2-3 DC Electrical Characteristics1 (Continued) Characteristics Symbol Min Typ Max Unit Not Recommended for New Design |
|
Link URL |
| Cho đến nay ALLDATASHEET có giúp ích cho doanh nghiệp của bạn hay không? [ DONATE ] |
Alldatasheet là | Quảng cáo | Liên lạc với chúng tôi | Chính sách bảo mật | Liên kết đến bảng dữ liệu | Trao đổi link | Tìm kiếm theo nhà sản xuất All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |