| công cụ tìm kiếm bảng dữ liệu linh kiện điện tử |
|
L9662 bảng dữ liệu(PDF) 75 Page - STMicroelectronics |
|
|
|||||||||||||||||||||||||||||
L9662 bảng dữ liệu(HTML) 75 Page - STMicroelectronics |
|
75 / 80 page ![]() DocID028325 Rev 1 75/80 L9662 Functional description 79 Codes are prioritized with the highest being 1 and the lowest being 7. Error code 011 is an “or-ed”combination of the following errors: Start bit error outside of selected operating range Data length error or stop bit error CRC/Parity Error of received Satellite Message Bit time error outside 75% 125% of start bit If in Hall Effect mode the status register under normal conditions will report a Register Empty (CHxSF2:CHxSF0='010'). If a fault is on the channel then either a Leakage to supply and no good data (CHxSF2:CHxSF0='101') or Leakage to ground (CHxSF2:CHxSF0='110') would be present. If in Raw data mode the status resister under normal conditions will report Register Empty (CHxSF2:CHxSF0='010'). If decoder is on then satellite data will be present (See Table 40 under protocol A or Protocol B) If decoder is off then D0 will contain data If a fault is on the channel then either a Leakage to supply and no good data (CHxSF2: CHxSF0='101') or Leakage to ground (CHxSF2:CHxSF0='110') would be present. Bit [D00] POR status 0 = Reset occurred. Bit cleared when read 1 = Normal 5 0 1 0 Register empty. No data received from satellite 4 0 1 1 Not valid data received i.e. – Start bit time outside valid range – Frame length – Bit time error – CRC/Parity error on sat received message (in this case there should be “register empty”) 3 1 0 0 Leakage to Supply Voltage at ICHx port and Not Good Data (data lost or register empty or not valid data) 2 1 0 1 Leakage to Supply at ICHx port & Good Data 1 1 1 0 Leakage to ground at ICHx port; (Over current detected switched OFF ICHx analog port, it can be still OFF if micro never wrote on CCR.D5:D4 to switch ON port) CCR D14=1 NA 1 1 1 CCR report is present on word ‘x’: Channel status is the response selected with bit D14 on CCR command Table 46. CCR D14 definition (continued) Priority CHxSF2 CHxSF1 CHxSF0 Description |
|
Link URL |
| Cho đến nay ALLDATASHEET có giúp ích cho doanh nghiệp của bạn hay không? [ DONATE ] |
Alldatasheet là | Quảng cáo | Liên lạc với chúng tôi | Chính sách bảo mật | Liên kết đến bảng dữ liệu | Trao đổi link | Tìm kiếm theo nhà sản xuất All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |