LPC64 datasheet(14/65 Pages) NXP

14 / 65 page

LPC1768_67_66_65_64_3

Product data sheet

Rev. 03 — 19 November 2009

14 of 65

NXP Semiconductors

LPC1768/67/66/65/64

32-bit ARM Cortex-M3 microcontroller

[1]

5 V tolerant pad providing digital I/O functions with TTL levels and hysteresis.

[2]

5 V tolerant pad providing digital I/O functions (with TTL levels and hysteresis) and analog input. When configured as a ADC input,

digital section of the pad is disabled and the pin is not 5 V tolerant.

[3]

5 V tolerant pad providing digital I/O with TTL levels and hysteresis and analog output function. When configured as the DAC output,

digital section of the pad is disabled.

[4]

Open-drain 5 V tolerant digital I/O pad, compatible with I2C-bus 400 kHz specification. This pad requires an external pull-up to provide

output functionality. When power is switched off, this pin connected to the I2C-bus is floating and does not disturb the I2C lines.

Open-drain configuration applies to all functions on this pin.

[5]

Pad provides digital I/O and USB functions. It is designed in accordance with the USB specification, revision 2.0 (Full-speed and

Low-speed mode only).

[6]

5 V tolerant pad with 5 ns glitch filter providing digital I/O functions with TTL levels and hysteresis.

[7]

5 V tolerant pad with 20 ns glitch filter providing digital I/O function with TTL levels and hysteresis.

[8]

Pad provides special analog functionality.

RTCX2

18[8]

Output from the RTC oscillator circuit.

VSS

31, 41,

55, 72,

97, 83[8]

ground: 0 V reference.

VSSA

11[8]

analog ground: 0 V reference. This should nominally be the same voltage as VSS,

but should be isolated to minimize noise and error.

VDD(3V3)

28, 54,

71, 96[8]

3.3 V supply voltage: This is the power supply voltage for the I/O ports.

VDD(REG)(3V3)

42, 84[8]

3.3 V voltage regulator supply voltage: This is the supply voltage for the on-chip

voltage regulator only.

VDDA

10[8]

analog 3.3 V pad supply voltage: This should be nominally the same voltage as

VDD(3V3) but should be isolated to minimize noise and error. This voltage is used to

power the ADC and DAC. This pin should be tied to 3.3 V if the ADC and DAC are

not used.

VREFP

12[8]

ADC positive reference voltage: This should be nominally the same voltage as

VDDA but should be isolated to minimize noise and error. Level on this pin is used

as a reference for ADC and DAC. This pin should be tied to 3.3 V if the ADC and

DAC are not used.

VREFN

ADC negative reference voltage: This should be nominally the same voltage as

VSS but should be isolated to minimize noise and error. Level on this pin is used as

a reference for ADC and DAC.

VBAT

19[8]

RTC pin power supply: 3.3 V on this pin supplies the power to the RTC

peripheral.

n.c.

not connected.

Table 3.

Pin description …continued

Symbol

Type

Description

LPC64 bảng dữ liệu(PDF) 14 Page - NXP Semiconductors

LPC64 bảng dữ liệu(HTML) 14 Page - NXP Semiconductors

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65

bảng dữ liệu tải về

Link URL