| công cụ tìm kiếm bảng dữ liệu linh kiện điện tử |
|
LPC64 bảng dữ liệu(PDF) 20 Page - NXP Semiconductors |
|
|
|||||||||||||||||||||||||||||
LPC64 bảng dữ liệu(HTML) 20 Page - NXP Semiconductors |
|
20 / 65 page ![]() LPC1768_67_66_65_64_3 © NXP B.V. 2009. All rights reserved. Product data sheet Rev. 03 — 19 November 2009 20 of 65 NXP Semiconductors LPC1768/67/66/65/64 32-bit ARM Cortex-M3 microcontroller Additionally, any pin on Port 0 and Port 2 (total of 42 pins) providing a digital function can be programmed to generate an interrupt on a rising edge, a falling edge, or both. The edge detection is asynchronous, so it may operate when clocks are not present such as during Power-down mode. Each enabled interrupt can be used to wake up the chip from Power-down mode. 7.10.1 Features • Bit level set and clear registers allow a single instruction to set or clear any number of bits in one port. • Direction control of individual bits. • All I/O default to inputs after reset. • Pull-up/pull-down resistor configuration and open-drain configuration can be programmed through the pin connect block for each GPIO pin. 7.11 Ethernet (LPC1768/67/66/64 only) Remark: The Ethernet controller is not available for part LPC1765. The Ethernet block contains a full featured 10 Mbit/s or 100 Mbit/s Ethernet MAC designed to provide optimized performance through the use of DMA hardware acceleration. Features include a generous suite of control registers, half or full duplex operation, flow control, control frames, hardware acceleration for transmit retry, receive packet filtering and wake-up on LAN activity. Automatic frame transmission and reception with scatter-gather DMA off-loads many operations from the CPU. The Ethernet block and the CPU share the ARM Cortex-M3 D-code and system bus through the AHB-multilayer matrix to access the various on-chip SRAM blocks for Ethernet data, control, and status information. The Ethernet block interfaces between an off-chip Ethernet PHY using the Reduced MII (RMII) protocol and the on-chip Media Independent Interface Management (MIIM) serial bus. The Ethernet block supports bus clock rates of up to 100 MHz. 7.11.1 Features • Ethernet standards support: – Supports 10 Mbit/s or 100 Mbit/s PHY devices including 10 Base-T, 100 Base-TX, 100 Base-FX, and 100 Base-T4. – Fully compliant with IEEE standard 802.3. – Fully compliant with 802.3x full duplex flow control and half duplex back pressure. – Flexible transmit and receive frame options. – Virtual Local Area Network (VLAN) frame support. • Memory management: – Independent transmit and receive buffers memory mapped to shared SRAM. – DMA managers with scatter/gather DMA and arrays of frame descriptors. – Memory traffic optimized by buffering and pre-fetching. |
|
Link URL |
| Cho đến nay ALLDATASHEET có giúp ích cho doanh nghiệp của bạn hay không? [ DONATE ] |
Alldatasheet là | Quảng cáo | Liên lạc với chúng tôi | Chính sách bảo mật | Liên kết đến bảng dữ liệu | Trao đổi link | Tìm kiếm theo nhà sản xuất All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |