| công cụ tìm kiếm bảng dữ liệu linh kiện điện tử |
|
M420000071 bảng dữ liệu(PDF) 40 Page - SPANSION |
|
|
|||||||||||||||||||||||||||||
M420000071 bảng dữ liệu(HTML) 40 Page - SPANSION |
|
40 / 90 page ![]() 38 Am42BDS6408H October 23, 2003 A D VA NCE I N FO RM ATIO N SecSi Sector Protection Bit Program Command The SecSi Sector Protection Bit Program Command programs the SecSi Sector Protection Bit, which pre- vents the SecSi sector memory from being cleared. If the SecSi Sector Protection Bit is verified as pro- grammed without margin, the SecSi Sector Protection Bit Program Command should be reissued to improve program margin. Exiting the VCC-level SecSi Sector Protection Bit Program Command is accomplished by writing the Read/Reset command. PPB Lock Bit Set Command The PPB Lock Bit Set command is used to set the PPB Lock bit if it is cleared either at reset or if the Password Unlock command was successfully exe- cuted. There is no PPB Lock Bit Clear command. Once the PPB Lock Bit is set, it cannot be cleared un- less the device is taken through a power-on clear or the Password Unlock command is executed. Upon set- ting the PPB Lock Bit, the PPBs are latched into the DYBs. If the Password Mode Locking Bit is set, the PPB Lock Bit status is reflected as set, even after a power-on reset cycle. Exiting the PPB Lock Bit Set command is accomplished by writing the Read/Reset command, only while in the Persistent Sector Protec- tion Mode. DYB Write Command The DYB Write command is used to set or clear a DYB for a given sector. The high order address bits (A21–A12) are issued at the same time as the code 01h or 00h on DQ7-DQ0. All other DQ data bus pins are ignored during the data write cycle. The DYBs are modifiable at any time, regardless of the state of the PPB or PPB Lock Bit. The DYBs are cleared at power-up or hardware reset. Exiting the DYB Write command is accomplished by writing the Read/Reset command. Password Unlock Command The Password Unlock command is used to clear the PPB Lock Bit so that the PPBs can be unlocked for modification, thereby allowing the PPBs to become ac- cessible for modification. The exact password must be entered in order for the unlocking function to occur. This command cannot be issued any faster than 2 µs at a time to prevent a hacker from running through the all 64-bit combinations in an attempt to correctly match a password. If the command is issued before the 2 µs execution window for each portion of the unlock, the command will be ignored. The Password Unlock function is accomplished by writing Password Unlock command and data to the de- vice to perform the clearing of the PPB Lock Bit. The password is 64 bits long, so the user must write the Password Unlock command 4 times. A1 and A0 are used for matching. Writing the Password Unlock com- mand is not address order specific. The lower address A1–A0= 00, the next Password Unlock command is to A1–A0= 01, then to A1–A0= 10, and finally to A1–A0= 11. Once the Password Unlock command is entered for all four words, the RDY pin goes LOW indicating that the device is busy. Approximately 1uSec is required for each portion of the unlock. Once the first portion of the password unlock completes (RDY is not driven and DQ6 does not toggle when read), the Password Un- lock command is issued again, only this time with the next part of the password. Four Password Unlock com- mands are required to successfully clear the PPB Lock Bit. As with the first Password Unlock command, the RDY signal goes LOW and reading the device re- sults in the DQ6 pin toggling on successive read oper- ations until complete. It is the responsibility of the microprocessor to keep track of the number of Pass- word Unlock commands, the order, and when to read the PPB Lock bit to confirm successful password un- lock. In order to relock the device into the Password Mode, the PPB Lock Bit Set command can be re-is- sued. PPB Program Command The PPB Program command is used to program, or set, a given PPB. Each PPB is individually pro- grammed (but is bulk erased with the other PPBs). The specific sector address (A21–A12) are written at the same time as the program command 60h with A6 = 0. If the PPB Lock Bit is set and the corresponding PPB is set for the sector, the PPB Program command will not execute and the command will time-out without programming the PPB. After programming a PPB, two additional cycles are needed to determine whether the PPB has been pro- grammed with margin. If the PPB has been pro- grammed without margin, the program command should be reissued to improve the program margin. The PPB Program command does not follow the Em- bedded Program algorithm. All PPB Erase Command The All PPB Erase command is used to erase all PPBs in bulk. There is no means for individually eras- ing a specific PPB. Unlike the PPB program, no spe- cific sector address is required. However, when the PPB erase command is written (60h) and A6 = 1, all Sector PPBs are erased in parallel. If the PPB Lock Bit is set the ALL PPB Erase command will not execute and the command will time-out without erasing the PPBs. After erasing the PPBs, two additional cycles are needed to determine whether the PPB has been erased with margin. If the PPBs has been erased with- |
|
Link URL |
| Cho đến nay ALLDATASHEET có giúp ích cho doanh nghiệp của bạn hay không? [ DONATE ] |
Alldatasheet là | Quảng cáo | Liên lạc với chúng tôi | Chính sách bảo mật | Liên kết đến bảng dữ liệu | Trao đổi link | Tìm kiếm theo nhà sản xuất All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |