| công cụ tìm kiếm bảng dữ liệu linh kiện điện tử |
|
M420000071 bảng dữ liệu(PDF) 34 Page - SPANSION |
|
|
|||||||||||||||||||||||||||||
M420000071 bảng dữ liệu(HTML) 34 Page - SPANSION |
|
34 / 90 page ![]() 32 Am42BDS6408H October 23, 2003 A D VA NCE I N FO RM ATIO N Table 13 describes the typical number of clock cycles (wait states) for various conditions with A14-A12 set to 101. Table 13. Wait States for Standard Handshaking * In the 8-, 16- and 32-word burst read modes, the address pointer does not cross 64-word boundaries (addresses which are multiples of 3Fh). The autoselect function allows the host system to determine whether the flash device is enabled for hands hak i ng. S ee the “Autos el ec t Command Sequence” section on page 33 for more information. Read Mode Configuration The device supports four different read modes: contin- uous mode, and 8, 16, and 32 word linear wrap around modes. A continuous sequence begins at the starting address and advances the address pointer until the burst operation is complete. If the highest address in the device is reached during the continuous burst read mode, the address pointer wraps around to the lowest address. For example, an eight-word linear read with wrap around begins on the starting address written to the device and then advances to the next 8 word boundary. The address pointer then returns to the 1st word after the previous eight word boundary, wrapping through the starting location. The sixteen- and thirty-two linear wrap around modes operate in a fashion similar to the eight-word mode. Table 14 shows the address bits and settings for the four read modes. Table 14. Read Mode Settings Note: Upon power-up or hardware reset the default setting is continuous. Burst Active Clock Edge Configuration By default, the device will deliver data on the rising edge of the clock after the initial synchronous access time. Subsequent outputs will also be on the following rising edges, barring any delays. The device can be set so that the falling clock edge is active for all synchro- nous accesses. Address bit A17 determines this set- ting; “1” for rising active, “0” for falling active. RDY Configuration By default, the device is set so that the RDY pin will output VOH whenever there is valid data on the outputs. The device can be set so that RDY goes active one data cycle before active data. Address bit A18 deter- mines this setting; “1” for RDY active with data, “0” for RDY active one clock cycle before valid data. In asyn- chronous mode, RDY is an open-drain output. Configuration Register Table 15 shows the address bits that determine the configuration register settings for various device func- tions. Conditions at Address Typical No. of Clock Cycles after AVD# Low Initial address 7 Initial address is 3E or 3Fh (or offset from these addresses by a multiple of 64) and is at boundary crossing* 7 Burst Modes Address Bits A16 A15 Continuous 0 0 8-word linear wrap around 0 1 16-word linear wrap around 1 0 32-word linear wrap around 1 1 |
|
Link URL |
| Cho đến nay ALLDATASHEET có giúp ích cho doanh nghiệp của bạn hay không? [ DONATE ] |
Alldatasheet là | Quảng cáo | Liên lạc với chúng tôi | Chính sách bảo mật | Liên kết đến bảng dữ liệu | Trao đổi link | Tìm kiếm theo nhà sản xuất All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |