IO13PDB0V0 datasheet(188/197 Pages) MICROSEMI

188 / 197 page

Datasheet Information

6- 6

R ev isio n 1 2

Revision 7

(continued)

The following sentence was removed from the "I/O Power-Up and Supply Voltage

Thresholds for Power-On Reset (Commercial and Industrial)" section because it is

incorrect (SAR 31047):

"The many different supplies can power up in any sequence with minimized current

spikes or surges."

2-4

Table 2-8 • Quiescent Supply Current Characteristics was divided into two tables: one

for power supplies configurations and one for quiescent supply current. SoC mode

was added to both tables (SAR 26378) and VCOMPLAx was removed from Table 2-8

• Power Supplies Configuration (SAR 29591). Quiescent supply current values were

updated in Table 2-9 • Quiescent Supply Current Characteristics (SAR 33067).

2-10

The "Total Static Power Consumption—PSTAT" section was revised: "NeNVM-BLOCKS *

PDC4" was removed from the equation for PSTAT (SAR 33067).

2-14

Table 2-14 • Different Components Contributing to Dynamic Power Consumption in

SmartFusion cSoCs and Table 2-15 • Different Components Contributing to the Static

Power Consumption in SmartFusion cSoCs were revised to reflect updates in the

SmartFusion power calculator (SARs 26405, 33067).

2-12,

2-13

Table 2-82 • A2F060 Global Resource is new (SAR 33132).

2-61

Output duty cycle was corrected to 50% in Table 2-83 • Electrical Characteristics of

the RC Oscillator. It was incorrectly noted as 1% previously. Operating current for 3.3

domain was added (SAR 32940).

2-61

Table 2-86 • SmartFusion CCC/PLL Specification was revised to add information and

measurements regarding CCC output peak-to-peak period jitter (SAR 32996).

2-63

The port names in the SRAM "Timing Waveforms", SRAM "Timing Characteristics"

tables, Figure 2-38 • FIFO Reset, and the FIFO "Timing Waveforms" tables were

revised to ensure consistency with the software names (SAR 29991).

2-66 to

2-75

Table 2-90 • eNVM Block Timing, Worst Commercial Case Conditions: TJ = 85°C,

VCC = 1.425 V was revised to correct the maximum frequencies (SAR 32410).

2-75

Table 2-97 • Comparator Performance Specifications was moved to the "SmartFusion

DC and Switching Characteristics" section from the SmartFusion Programmable

Analog User’s Guide because the information is extracted from characterization (SAR

24298).

2-83

The hysteresis section in Table 2-97 • Comparator Performance Specifications was

revised (SAR 33158).

2-83

The "SmartFusion Development Tools" was extensively updated (SAR 33216).

3-1

The text following Table 4-2 • JTAG Pin Descriptions was updated to add information

on control of the JTAGSEL pin. Manual jumpers on the evaluation and development

kits allow manual selection of this function for J-Link and ULINK debuggers (SAR

25592).

4-7

Revision

Changes

Page

IO13PDB0V0 bảng dữ liệu(PDF) 188 Page - Microsemi Corporation

IO13PDB0V0 bảng dữ liệu(HTML) 188 Page - Microsemi Corporation

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

bảng dữ liệu tải về

Link URL