22017 datasheet(102/120 Pages) ITT

102 / 120 page

DPGM/DPJM/DPJMB

Assembly Procedures

102

www.ittcannon.com

Dimensions shown in inch (mm)

Specifications and dimensions subject to change

Wiring and Crimping Contacts

Wires should be stripped to the dimension

appropriate to the contact use

#20 Contact

#2018, #16 & #12 Contact

Contact Size

3/16 (4.76)

.089 DIA. MAX

(2.26)

1/4 (6.35)

SUPPORT OMITTED ON

DPJMB CONTACT

WIRE

Contact

Tool

Description

Assembly

Number

Contact

#20

#16

#12

CET - 20A

CET - 16

CET - 12

CET - C1

038889-0100

038888-0000

038890-0000

038869-0000

Coaxial

50-75,95 &

150 ohm

#20

#16

#12

After the contacts have been crimped, they should

be threaded through the junction shell and inserted

with the tools shown below. It is recommended that

the contacts be inserted in the center horizontal

row first, then work to the top and bottom horizon-

tal rows.

If it is necessary at any time to remove contacts,

this may be accomplished with an impact extraction

tool. Simply place the correct tool on the engaging

end of the contact and push. A reversible tip is

provided for pins and sockets.

1. CONTACT INTO CRIMP TOOL

Drop contact into crimp tool, it will locate on the contact shoulder.

2. WIRE INTO CONTACT

Take wire stripped to dimensions above, and push into the contact crimp pot until it is completely home.

Where outside diameter of wire in the #12 or COAXIAL contact is less than .096 (2.44), a rubber

bushing most be slipped over the wire before crimping (see page 103).

3. CRIMP

Squeeze the crimp tool to secure the wire into the contact. It is not possible to remove the contact from

the crimp tool until crimp is completed.

4. REMOVED WIRED CONTACT FROM TOOL

5. INSPECT

If wires are stripped and crimped correctly, the wire will be visible through the small inspection hole in

the contact.

CIT - 20

CIT - 16

CIT - 12

CIT - C2

038894-0000

038895-0000

038896-0000

038901-0000

Coaxial

50-75,95 &

150 ohm

Tool

Description

Assembly

Number

CONTACT

#20

#2018

#16

#12

Contact Insertion (DPGM/DPJM)

Inserting #20 & #16

Contacts

Inserting Coaxial & #12

Contacts

Extracting #20 & #16

Contacts

Extracting Coaxial & #12

Contacts

Contact Extraction (DPGM/DPJM

22017 bảng dữ liệu(PDF) 102 Page - ITT Industries

22017 bảng dữ liệu(HTML) 102 Page - ITT Industries

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

bảng dữ liệu tải về

Link URL