MPC8610EC datasheet(31/96 Pages) FREESCALE

31 / 96 page

Electrical Characteristics

MPC8610 Integrated Host Processor Hardware Specifications, Rev. 0

Freescale Semiconductor

NOTE

For the ADDR/CMD setup and hold specifications in Table 22, it is assumed that the clock

control register is set to adjust the memory clocks by 1/2 applied cycle.

Figure 5 shows the DDR SDRAM output timing for the MCK to MDQS skew measurement (tDDKHMH).

Figure 5. Timing Diagram for tDDKHMH

MDQS epilogue end

tDDKHME

–0.6

0.6

Notes:

1. The symbols used for timing specifications follow the pattern of t(first two letters of functional block)(signal)(state)(reference)(state) for

inputs and t(first two letters of functional block)(reference)(state)(signal)(state) for outputs. Output hold time can be read as DDR timing

(DD) from the rising or falling edge of the reference clock (KH or KL) until the output went invalid (AX or DX). For example,

tDDKHAS symbolizes DDR timing (DD) for the time tMCK memory clock reference (K) goes from the high (H) state until outputs

(A) are setup (S) or output valid time. Also, tDDKLDX symbolizes DDR timing (DD) for the time tMCK memory clock reference

(K) goes low (L) until data outputs (D) are invalid (X) or data output hold time.

2. All MCK/MCK referenced measurements are made from the crossing of the two signals ±0.1 V.

3. ADDR/CMD includes all DDR SDRAM output signals except MCK/MCK, MCS, and MDQ/MECC/MDM/MDQS.

4. Note that tDDKHMH follows the symbol conventions described in note 1. For example, tDDKHMH describes the DDR timing (DD)

from the rising edge of the MCK[n] clock (KH) until the MDQS signal is valid (MH). tDDKHMH can be modified through control

of the DQSS override bits in the TIMING_CFG_2 register. This will typically be set to the same delay as the clock adjust in

the CLK_CNTL register. The timing parameters listed in the table assume that these 2 parameters have been set to the same

adjustment value. See the

MPC8610 Integrated Host Processor Reference Manual, for a description and understanding of

the timing modifications enabled by use of these bits.

5. Determined by maximum possible skew between a data strobe (MDQS) and any corresponding bit of data (MDQ), ECC

(MECC), or data mask (MDM). The data strobe should be centered inside of the data eye at the pins of the microprocessor.

6. All outputs are referenced to the rising edge of MCK[

n] at the pins of the microprocessor. Note that tDDKHMP follows the

symbol conventions described in note 1.

7. Maximum DDR1 frequency is 400 MHz. Minimum DDR2 frequency is 400 MHz.

8. Per the JEDEC spec the DDR2 duty cycle at 400 and 533 MHz is the low and high cycle time values.

Table 22. DDR SDRAM Output AC Timing Specifications (continued)

At recommended operating conditions.

Parameter

Symbol1

Min

Max

Unit

Notes

MDQS

MCK[

tMCK

tDDKHMHmax) = 0.6 ns

tDDKHMH(min) = –0.6 ns

MDQS

MPC8610EC bảng dữ liệu(PDF) 31 Page - Freescale Semiconductor, Inc

MPC8610EC bảng dữ liệu(HTML) 31 Page - Freescale Semiconductor, Inc

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96

bảng dữ liệu tải về

Link URL