PSD913F2 datasheet(28/94 Pages) STMICROELECTRONICS

28 / 94 page

PSD9XX Family

Preliminary Information

The

PSD9XX

Functional

Blocks

(cont.)

9.1.1.7 Unlock Bypass Instruction (PSD934F2 and PSD954F2 only)

The unlock bypass feature allows the system to program bytes to the flash memories

faster than using the standard program instruction. The unlock bypass instruction is

initiated by first writing two unlock cycles. This is followed by a third write cycle containing

the unlock bypass command, 20h (see Table 9). The flash memory then enters the unlock

bypass mode. A two-cycle Unlock Bypass Program instruction is all that is required to

program in this mode. The first cycle in this instruction contains the unlock bypass

programm command, A0h; the second cycle contains the program address and data.

Additional data is programmed in the same manner. This mode dispenses with the initial

two unlock cycles requiredc in the standard program instruction, resulting in faster total

programming time. During the unlock bypass mode, only the Unlock Bypass Program and

Unlock Bypass Reset instructions are valid. To exit the unlock bypass mode, the system

must issue the two-cycle unlock bypass reset instruction. The first cycle must contain the

data 90h; the second cycle the data 00h. Addresses are don’t care for both cycles. The

falsh memory then returns to reading array data mode.

9.1.1.8 Erasing Flash Memory

9.1.1.8.1. Flash Bulk Erase Instruction

The Flash Bulk Erase instruction uses six write operations followed by a Read operation of

the status register, as described in Table 9. If any byte of the Bulk Erase instruction is

wrong, the Bulk Erase instruction aborts and the device is reset to the Read Flash memory

status.

During a Bulk Erase, the memory status may be checked by reading status bits DQ5, DQ6,

and DQ7, as detailed in section 9.1.1.6. The Error bit (DQ5) returns a ‘1’ if there has been

an Erase Failure (maximum number of erase cycles have been executed).

It is not necessary to program the array with 00h because the PSD9XX will automatically

do this before erasing to 0FFh.

During execution of the Bulk Erase instruction, the Flash memory will not accept any

instructions.

9.1.1.8.2 Flash Sector Erase Instruction

The Sector Erase instruction uses six write operations, as described in Table 9. Additional

Flash Sector Erase confirm commands and Flash sector addresses can be written

subsequently to erase other Flash sectors in parallel, without further coded cycles, if the

additional instruction is transmitted in a shorter time than the timeout period of about

100 µs. The input of a new Sector Erase instruction will restart the time-out period.

The status of the internal timer can be monitored through the level of DQ3 (Erase time-out

bit). If DQ3 is ‘0’, the Sector Erase instruction has been received and the timeout is

counting. If DQ3 is ‘1’, the timeout has expired and the PSD9XX is busy erasing the Flash

sector(s). Before and during Erase timeout, any instruction other than Erase suspend and

Erase Resume will abort the instruction and reset the device to Read Array mode.

It is not necessary to program the Flash sector with 00h as the PSD9XX will do this

automatically before erasing (byte=FFh).

During a Sector Erase, the memory status may be checked by reading status bits DQ5,

DQ6, and DQ7, as detailed in section 9.1.1.6.

During execution of the erase instruction, the Flash block logic accepts only Reset and

Erase Suspend instructions. Erasure of one Flash sector may be suspended, in order to

read data from another Flash sector, and then resumed.

PSD913F2 bảng dữ liệu(PDF) 28 Page - STMicroelectronics

PSD913F2 bảng dữ liệu(HTML) 28 Page - STMicroelectronics

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94

bảng dữ liệu tải về

Link URL