PSD913F2 datasheet(22/94 Pages) STMICROELECTRONICS

22 / 94 page

PSD9XX Family

Preliminary Information

FS0-7

Instruction

CSBOOT0-3 Cycle 1 Cycle 2 Cycle 3

Cycle 4

Cycle5

Cycle 6

Cycle 7

Read (Note 5)

“Read”

RA RD

Read Main Flash ID

AAh

55h

90h

“Read”

(Notes 6,13)

@555h

@AAAh

@555h

@x01h

Read Sector Protection

AAh

55h

90h

“Read”

(Notes 6,8,13)

@555h

@AAAh

@555h

00h or 01h

@x02h

Program a Flash Byte

AAh

55h

A0h

PD@PA

@555h

@AAAh

@555h

Erase One Flash Sector

AAh

55h

80h

AAh

55h

30h

@555h

@AAAh

@555h

@AAAh

@SA

@next SA

(Note 7)

Erase Flash Block

AAh

55h

80h

AAh

55h

10h

(Bulk Erase)

@555h

@AAAh

@555h

@AAAh

@555h

Suspend Sector Erase

B0h

(Note 11)

@xxxh

Resume Sector Erase

30h

(Note 12)

@xxxh

Reset (Note 6)

F0 @ any

address

Unlock Bypass

AAh

55h

20h

(Note 14)

@555h

@AAAh

@555h

Unlock Bypass Program

A0h

PD@PA

(Note 9,14)

@xxxh

Unlock Bypass Reset

90h

00h

(Note 10,14)

@xxxh

Table 9. Instructions

= Don’t Care.

RA = Address of the memory location to be read.

RD = Data read from location RA during read operation.

PA = Address of the memory location to be programmed. Addresses are latched on the falling edge of the WR#

(CNTL0) pulse.

PD = Data to be programmed at location PA. Data is latched o the rising edge of WR# (CNTL0) pulse.

SA = Address of the sector to be erased or verified. The chip select (FS0-7 or CSBOOT0-3) of the sector to be

erased must be active (high).

NOTES:

All bus cycles are write bus cycle except the ones with the “read” label.

All values are in hexadecimal.

FS0-7 and CSBOOT0-3 are active high and are defined in PSDsoft.

Only Address bits A11-A0 are used in Instruction decoding. A15-12 (or A16-A12) are don’t care.

No unlock or command cycles required when device is in read mode.

The Reset command is required to return to the read mode after reading the Flash ID, Sector Protect status

or if DQ5 (error flag) goes high.

Additional sectors to be erased must be entered within 80µs.

The data is 00h for an unprotected sector and 01h for a protected sector. In the fourth cycle, the sector chip

select is active and (A1 = 1, A0 = 0).

The Unlock Bypass command is required prior to the Unlock Bypass Program command.

10. The Unlock Bypass Reset command is required to return to reading array data when the device is in the

Unlock Bypass mode.

11. The system may read and program functions in non-erasing sectors, read the Flash ID or read the Sector

Protect status, when in the Erase Suspend mode. The erase Suspend command is valid only during a sector

erase operation.

12. The Erase Resume command is valid only during the Erase Suspend mode.

13. The MCU cannot invoke these instructions while executing code from the same Flash memory for which the

instruction is intended. The MCU must fetch, for example, codes from the secondary block when reading the

Sector Protection Status of the main Flash.

14. Available to PSD934F2 and PSD954F2 devices only.

The

PSD9XX

Functional

Blocks

(cont.)

PSD913F2 bảng dữ liệu(PDF) 22 Page - STMicroelectronics

PSD913F2 bảng dữ liệu(HTML) 22 Page - STMicroelectronics

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94

bảng dữ liệu tải về

Link URL