DS31256 datasheet(138/183 Pages) MAXIM

138 / 183 page

DS31256 256-Channel, High-Throughput HDLC Controller

138 of 183

10.2.1 Command Bits (PCMD0)

Bit 0/I/O Space Control (IOC). This read-only bit is forced to 0 by the device to indicate that it does not respond

to I/O space accesses.

Bit 1/Memory Space Control (MSC). This read/write bit controls whether or not the device responds to accesses

by the PCI bus to the memory space (the internal device configuration registers). When this bit is set to 0, the

device ignores accesses attempted to the internal configuration registers. When set to 1, the device allows accesses

to the internal configuration registers. This bit should be set to 0 when the local bus is operated in the

configuration mode. This bit is forced to 0 when a hardware reset is initiated through the

PRST pin.

0 = ignore accesses to the internal device configuration registers

1 = allow accesses to the internal device configuration registers

Bit 2/Master Control (MASC). This read/write bit controls whether or not the device can act as a master on the

PCI bus. When this bit is set to 0, the device cannot act as a master. When it is set to 1, the device can act as a bus

master. This bit is forced to 0 when a hardware reset is initiated through the

PRST pin.

0 = deny the device from operating as a bus master

1 = allow the device to operate as a bus master

Bit 3/Special Cycle Control (SCC). This read-only bit is forced to 0 by the device to indicate that it cannot

decode special cycle operations.

Bit 4/Memory Write and Invalidate Command Enable (MWEN). This read-only bit is forced to 0 by the

device to indicate that it cannot generate the memory write and invalidate command.

Bit 5/VGA Control (VGA). This read-only bit is forced to 0 by the device to indicate that it is not a VGA-

compatible device.

Bit 6/Parity Error Response Control (PARC). This read/write bit controls whether or not the device should

ignore parity errors. When this bit is set to 0, the device ignores any parity errors that it detects and continues to

operate normally. When this bit is set to 1, the device must act on parity errors. This bit is forced to 0 when a

hardware reset is initiated through the

PRST pin.

0 = ignore parity errors

1 = act on parity errors

Bit 7/Address Stepping Control (STEPC). This read-only bit is forced to 0 by the device to indicate that it is not

capable of address/data stepping.

Bit 8/PCI System Error Control (PSEC). This read/write bit controls whether or not the device should enable

the

PSERR output pin. When this bit is set to 0, the device disables the PSERR pin. When this bit is set to 1, the

device enables the

PSERR pin. This bit is forced to 0 when a hardware reset is initiated through the PRST pin.

0 = disable the

PSERR pin

1 = enable the

PSERR pin

Bit 9/Fast Back-to-Back Master Enable (FBBEN). This read-only bit is forced to 0 by the device to indicate that

it is not capable of generating fast back-to-back transactions to different agents.

Bits 10 to 15/Reserved. These read-only bits are forced to 0 by the device.

DS31256 bảng dữ liệu(PDF) 138 Page - Maxim Integrated Products

DS31256 bảng dữ liệu(HTML) 138 Page - Maxim Integrated Products

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

bảng dữ liệu tải về

Link URL