M30622ECTFP datasheet(104/184 Pages) MITSUBISHI

104 / 184 page

104

Tentative Specifications REV.A

Mitsubishi microcomputers

M16C / 62T Group

SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER

Specifications in this manual are tentative and subject to change.

Under

development

Timers’ functions for three-phase motor control

Figure 1.18.5 shows the block diagram for three-phase waveform mode. In three-phase waveform mode,

___

the positive-phase waveforms (U phase, V phase, and W phase) and negative waveforms (U phase, V

___

phase, and W phase), six waveforms in total, are output from P80,P81, P72, P73, P74, and P75 as active

___

on the “L” level. Of the timers used in this mode, timer A4 controls the U phase and U phase, timer A1

___

controls the V phase and V phase, and timer A2 controls the W phase and W phase respectively; timer B2

controls the periods of one-shot pulse output from timers A4, A1, and A2.

In outputting a waveform, dead time can be set so as to cause the “L” level of the positive waveform

___

output (U phase, V phase, and W phase) not to lap over the “L” level of the negative waveform output (U

___

phase, V phase, and W phase).

To set short circuit time, use three 8-bit timers sharing the reload register for setting dead time. A value

from 1 through 255 can be set as the count of the timer for setting dead time. The timer for setting dead

time works as a one-shot timer. If a value is written to the dead timer (034C16), the value is written to the

reload register shared by the three timers for setting dead time.

Any of the timers for setting dead time takes the value of the reload register into its counter, if a start

trigger comes from its corresponding timer, and performs a down count in line with the clock source

selected by the dead time timer count source select bit (bit 2 at 034916). The timer can receive another

trigger again before the workings due to the previous trigger are completed. In this instance, the timer

performs a down count from the reload register’s content after its transfer, provoked by the trigger, to the

timer for setting dead time.

Since the timer for setting dead time works as a one-shot timer, it starts outputting pulses if a trigger

comes; it stops outputting pulses as soon as its content becomes 0016, and waits for the next trigger to

come.

___

The positive waveforms (U phase, V phase, and W phase) and the negative waveforms (U phase, V

___

phase, and W phase) in three-phase waveform mode are output from respective ports by means of

setting “1” in the output control bit (bit 3 at 034816). Setting “0” in this bit causes the ports to be the state

of set by port direction register. This bit can be set to “0” not only by use of the applicable instruction, but

_______

by entering a falling edge in the NMI terminal or by resetting. Also, if “1” is set in the positive and negative

phases concurrent L output disable function enable bit (bit 4 at 034816) causes one of the pairs of U

___

phase and U phase, V phase and V phase, and W phase and W phase concurrently go to “L”, as a result,

the port become the state of set by port direction register.

M30622ECTFP bảng dữ liệu(PDF) 104 Page - Mitsubishi Electric Semiconductor

M30622ECTFP bảng dữ liệu(HTML) 104 Page - Mitsubishi Electric Semiconductor

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

bảng dữ liệu tải về

Link URL