| công cụ tìm kiếm bảng dữ liệu linh kiện điện tử |
|
M30622ECTFP bảng dữ liệu(PDF) 88 Page - Mitsubishi Electric Semiconductor |
|
|
|||||||||||||||||||||||||||||
M30622ECTFP bảng dữ liệu(HTML) 88 Page - Mitsubishi Electric Semiconductor |
|
88 / 184 page ![]() 88 Tentative Specifications REV.A Mitsubishi microcomputers M16C / 62T Group SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER Specifications in this manual are tentative and subject to change. Under development Timer A (2) Event counter mode In this mode, the timer counts an external signal or an internal timer’s overflow. Timers A0 and A1 can count a single-phase external signal. Timers A2, A3, and A4 can count a single-phase and a two-phase external signal. Table 1.17.2 lists timer specifications when counting a single-phase external signal. Figure 1.17.8 shows the timer Ai mode register in event counter mode. Table 1.17.3 lists timer specifications when counting a two-phase external signal. Figure 1.17.9 shows the timer Ai mode register in event counter mode. Figure 1.17.8. Timer Ai mode register in event counter mode Timer Ai mode register Note 1: In event counter mode, the count source is selected by the event / trigger select bit (addresses 038216 and 038316). Note 2: The settings of the corresponding port register and port direction register are invalid. Note 3: Valid only when counting an external signal. Note 4: When an “L” signal is input to the TAiOUT pin, the downcount is activated. When “H”, the upcount is activated. Set the corresponding port direction register to “0”. Note 5: In Timer A1 and A2 mode register of M30623(80-pin package), set these bits to “0”. Symbol Address When reset TAiMR(i = 0, 1) 039616, 039716 0016 W R b7 b6 b5 b4 b3 b2 b1 b0 Operation mode select bit 0 1 : Event counter mode (Note 1) b1 b0 TMOD0 MR0 Pulse output function select bit (Note 5) 0 : Pulse is not output (TAiOUT pin is a normal port pin) 1 : Pulse is output (Note 2) (TAiOUT pin is a pulse output pin) Count polarity select bit (Note 3,Note 5) MR2 MR1 MR3 0 (Must always be fixed to “0” in event counter mode) TCK0 Count operation type select bit 01 0 0 : Counts external signal's falling edge 1 : Counts external signal's rising edge Up/down switching cause select bit (Note 5) 0 : Up/down flag's content 1 : TAiOUT pin's input signal (Note 4) 0 : Reload type 1 : Free-run type Bit symbol Bit name Function RW TCK1 Invalid in event counter mode Can be “0” or “1” TMOD1 Item Specification Count source • External signals input to TAiIN pin (effective edge can be selected by software) • TB2 overflow, TAj overflow Count operation • Up count or down count can be selected by external signal or software • When the timer overflows or underflows, it reloads the reload register con tents before continuing counting (Note) Divide ratio 1/ (FFFF16 - n + 1) for up count 1/ (n + 1) for down count n : Set value Count start condition Count start flag is set (= 1) Count stop condition Count start flag is reset (= 0) Interrupt request generation timing The timer overflows or underflows TAiIN pin function Programmable I/O port or count source input TAiOUT pin function Programmable I/O port, pulse output, or up/down count select input Read from timer Count value can be read out by reading timer Ai register Write to timer • When counting stopped When a value is written to timer Ai register, it is written to both reload register and counter • When counting in progress When a value is written to timer Ai register, it is written to only reload register (Transferred to counter at next reload time) Select function • Free-run count function Even when the timer overflows or underflows, the reload register content is not reloaded to it • Pulse output function Each time the timer overflows or underflows, the TAiOUT pin’s polarity is reversed Note 1: This does not apply when the free-run function is selected. Note 2: M30623(80-pin package) does not have I/O pins(TAiIN,TAiOUT) for timer A1 and A2. Table 1.17.2. Timer specifications in event counter mode (when not processing two-phase pulse signal) |
|
Link URL |
| Cho đến nay ALLDATASHEET có giúp ích cho doanh nghiệp của bạn hay không? [ DONATE ] |
Alldatasheet là | Quảng cáo | Liên lạc với chúng tôi | Chính sách bảo mật | Liên kết đến bảng dữ liệu | Trao đổi link | Tìm kiếm theo nhà sản xuất All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |