M30622ECTFP datasheet(94/184 Pages) MITSUBISHI

94 / 184 page

Tentative Specifications REV.A

Mitsubishi microcomputers

M16C / 62T Group

SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER

Specifications in this manual are tentative and subject to change.

Under

development

Timer B

Figure 1.17.14 shows the block diagram of timer B. Figures 1.17.15 and 1.17.16 show the timer B-related

registers.

Use the timer Bi mode register (i = 0 to 2) bits 0 and 1 to choose the desired mode.

Timer B has three operation modes listed as follows:

Figure 1.17.15. Timer B-related registers (1)

Timer Bi mode register

Symbol

Address

When reset

TBiMR(i = 0 to 5) 039B16 to 039D16

00XX00002

035B16 to 035D16

00XX00002

Bit name

Function

Bit symbol

0 0 : Timer mode

0 1 : Event counter mode

1 0 : Pulse period/pulse width

measurement mode (Note 3)

1 1 : Inhibited

b1 b0

TCK1

MR3

MR2

MR1

TMOD1

MR0

TMOD0

TCK0

Function varies with each operation mode

Count source select bit

(Function varies with each operation mode)

Operation mode select bit

(Note 1)

(Note 2)

Note 1: Timer B0, timer B3.

Note 2: Timer B1, timer B2, timer B4, timer B5.

Note 3: In the timer B1 mode register of M30623(80-pin package), do not use this mode,

because timer B1 has no input pin.

Clock source selection

(address 038016)

• Event counter

• Timer

• Pulse period/pulse width measurement

Reload register (16)

Low-order 8 bits

High-order 8 bits

Data bus low-order bits

Data bus high-order bits

f32

TBj overflow

(j = i – 1. Note, however,

j = 2 when i = 0,

j = 5 when i = 3)

Can be selected in only

event counter mode

Count start flag

fC32

Polarity switching

and edge pulse

TBiIN

(i = 0 to 5)

Counter reset circuit

Counter (16)

TBi

Address

TBj

Timer B0

039116 039016

Timer B2

Timer B1

039316 039216

Timer B0

Timer B2

039516 039416

Timer B1

Timer B3

035116 035016

Timer B5

Timer B4

035316 035216

Timer B3

Timer B5

035516 035416

Timer B4

Note 1: In M30623(80-pin package), do not select the function using TB1IN,

because it is not connected to the external pin.

Note 2: The TB5IN pin is shared with the TA0IN pin, RxD2, and SCL pin.

• Timer mode: The timer counts an internal count source.

• Event counter mode: The timer counts pulses from an external source or a timer overflow.

• Pulse period/pulse width measuring mode: The timer measures an external signal's pulse period or pulse width.

Figure 1.17.14. Block diagram of timer B

But, M30623(80-pin package), timer B1 has no input pin, so funcs as the internal timer.

M30622ECTFP bảng dữ liệu(PDF) 94 Page - Mitsubishi Electric Semiconductor

M30622ECTFP bảng dữ liệu(HTML) 94 Page - Mitsubishi Electric Semiconductor

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

bảng dữ liệu tải về

Link URL