| công cụ tìm kiếm bảng dữ liệu linh kiện điện tử |
|
S25FS256S bảng dữ liệu(PDF) 97 Page - SPANSION |
|
|
|||||||||||||||||||||||||||||
S25FS256S bảng dữ liệu(HTML) 97 Page - SPANSION |
|
97 / 154 page ![]() November 6, 2013 S25FS-S_00_04 S25FS-S Family 97 Da ta Shee t (Prelim i nar y ) Notes: 1. The Status Register originally shows 00h when the device is first shipped from Spansion to the customer. 2. Hardware protection is disabled when Quad Mode is enabled (CR1V[1] = 1). WP# becomes IO2; therefore, it cannot be utilized. 10.3.5 Write Enable (WREN 06h) The Write Enable (WREN) command sets the Write Enable Latch (WEL) bit of the Status Register 1 (SR1V[1]) to a 0. The Write Enable Latch (WEL) bit must be set to a 1 by issuing the Write Enable (WREN) command to enable write, program and erase commands. CS# must be driven into the logic high state after the eighth bit of the instruction byte has been latched in on SI. Without CS# being driven to the logic high state after the eighth bit of the instruction byte has been latched in on SI, the write enable operation will not be executed. Figure 10.13 Write Enable (WREN) Command Sequence This command is also supported in QPI Mode. In QPI Mode the instruction is shifted in on IO0-IO3, two clock cycles per byte. Figure 10.14 Write Enable (WREN) Command Sequence QPI Mode Table 10.2 Block Protection Modes WP# SRWD Bit Mode Write Protection of Registers Memory Content Protected Area Unprotected Area 11 Software Protected Status and Configuration Registers are Writable (if WREN command has set the WEL bit). The values in the SRWD, BP2, BP1, and BP0 bits and those in the Configuration Register can be changed. Protected against Page Program, Sector Erase, and Bulk Erase. Ready to accept Page Program, and Sector Erase commands. 10 00 01 Hardware Protected Status and Configuration Registers are Hardware Write Protected. The values in the SRWD, BP2, BP1, and BP0 bits and those in the Configuration Register cannot be changed. Protected against Page Program, Sector Erase, and Bulk Erase. Ready to accept Page Program or Erase commands. CS# SCK SI SO Phase 7 6 5 4 3 2 1 0 Instruction CS# SCLK IO0 IO1 IO2 IO3 Phase 4 0 5 1 6 2 7 3 Instruction |
|
Link URL |
| Cho đến nay ALLDATASHEET có giúp ích cho doanh nghiệp của bạn hay không? [ DONATE ] |
Alldatasheet là | Quảng cáo | Liên lạc với chúng tôi | Chính sách bảo mật | Liên kết đến bảng dữ liệu | Trao đổi link | Tìm kiếm theo nhà sản xuất All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |