| công cụ tìm kiếm bảng dữ liệu linh kiện điện tử |
|
TLK3114SCZPV bảng dữ liệu(PDF) 35 Page - Texas Instruments |
|
|
|||||||||||||||||||||||||||||
TLK3114SCZPV bảng dữ liệu(HTML) 35 Page - Texas Instruments |
|
35 / 68 page ![]() 3−17 RDA[7:0] D D S I I Packet D D ... D D D D I I S I D D IPG RDB[7:0] D D D I I D D ... D D T D I I D I D D RDC[7:0] D D D I I D D ... D D I D I I D I D D RDD[7:0] D D D I I D D ... D D I D I I D I D D Output S = Start of Packet D = Data T = End of Packet A = K28.3 K = K28.5 R = K28.0 I = Idle RXA D D S R K D D ... D D D D R A K R D S RXB D D D R K D D ... D D T D R A K R D D RXC D D D R K D D ... D D K D R A K R D D RXD D D D R K D D ... D D K D R A K R D D Input Dropped Column Figure 3−16. Clock Tolerance Compensation: Drop The R code is disparity neutral, allowing its removal or insertion without affecting the current running disparity of each channel’s serial stream. The clock tolerance compensation circuit also converts XAUI A, K, and R characters to XGMII idles, as illustrated in Figure 3−16. 3.20 Parallel-to-Serial Shift Register The parallel-to-serial shift register on each channel takes in 10-bit wide data from either the 8-b/10-b encoders, if enabled, or directly from the transmit data bus and converts it to a serial stream. The shift register is clocked by the internally generated bit clock, which is 10 times the reference clock (RFCP/RFCN) frequency. The least significant bit (LSB) for each channel is transmitted first. 3.21 Serial-to-Parallel Shift Register For each channel, serial data is received on the RXxP/RXxN terminals. The interpolator and clock recovery circuit locks to the data stream if the clock to be recovered is within ±100 PPM of the internally generated bit rate clock. The recovered clock retimes the input data stream. The serial data is then clocked into the serial-to-parallel shift registers. If enabled, the 10-bit wide parallel data is then fed into 8-b/10-b decoders. If the TLK3114SC device is configured in one of the synchronized channel modes, the parallel data for each channel is fed into a FIFO buffer where the output is synchronized to RCA. If the TLK3114SC device is configured in one of the independent channel modes, the parallel data for each channel is output synchronized to each channel’s recovered clock. Transmitting data across PCB or cables attenuates the high frequency content of the signal. This reduces the timing margin for the receiver and clock recovery circuits. The TLK3114SC device applies a filter at the receiver to invert the effects of the interconnect, or equalize and recover some of the lost margin. This maximizes the receiver’s ability to recover transmitted data. |
|
Link URL |
| Cho đến nay ALLDATASHEET có giúp ích cho doanh nghiệp của bạn hay không? [ DONATE ] |
Alldatasheet là | Quảng cáo | Liên lạc với chúng tôi | Chính sách bảo mật | Liên kết đến bảng dữ liệu | Trao đổi link | Tìm kiếm theo nhà sản xuất All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |