| công cụ tìm kiếm bảng dữ liệu linh kiện điện tử |
|
MPL460AT-I/4LB bảng dữ liệu(PDF) 21 Page - Microchip Technology |
|
|
|||||||||||||||||||||||||||||
MPL460AT-I/4LB bảng dữ liệu(HTML) 21 Page - Microchip Technology |
|
21 / 48 page ![]() PL460 Bootloader Data Sheet © 2020-2023 Microchip Technology Inc. and its subsidiaries DS60001666D - 21 7.4.2. Bootloader Hardware Signature Each frame received from the host (write or read frame) will be acknowledged with a 32-bit signature through the MISO signal. This is used to give the bootloader’s signature and the state of the system to the host. This frame is composed of the following: MISO B31 B16 B17 B14 B15 B12 B13 B10 B11 B8 B9 B7 B1 B2 B0 CS SCK MOSI A31 A16 A17 A14 A15 A12 A13 A10 A11 A8 A9 A7 A1 A2 A0 C15 X BOOT_SIGN RST_STATUS RESERVED FREE AES Bit Name Value 31..17 BOOT_SIGN 010101100011010 16 RST_STATUS USER_RST 15 CM7_RESET 14 WDT_RESET 13 BOOT_FUSE — 12 CHIP_ID — 11 RESERVED — 10 HSM_FUSE — 9 AES_FUSES AES_DIS 8 AES_128 7..2 RESERVED — 1..0 FREE_FUSES — 7.4.3. Write Process The command used to write on a unique address is CMD = 0x0000. The command used to write on several consecutive addresses is CMD = 0x0001. In this case, it will be sent the 32 bits of the initial address, 16 bits of the command (0x0001) and as many consecutive words (32 bits) as are wanted to write. Regarding the decryption packets, the commands to write the number of decryption packets (CMD = 0x0004), the initial vector of decryption (CMD = 0x0005) or the decryption signature to test if decryption is correct (CMD = 0x0006), the address of the frame is not taken into account and it can be composed of any address value. To write the decryption packet, only the last 15 bits are taken into account. In the case of decryption initial vector and decryption signature where it is necessary to send the 128-bit value as data, it is made in the same way as the write process at consecutive addresses, sending 4 consecutive words (32 bits). To write a fuse box, the Buffer register must be written in advance (CMD = 0x0007) and then the Tamper registers of KEY_ENC_BOX, KEY_TAG_BOX or CONTROL_BOX must be written with the content of the buffer (CMD = 0x0008, CMD = 0x0009 and CMD = 0x000B respectively). Finally, to |
|
Link URL |
| Cho đến nay ALLDATASHEET có giúp ích cho doanh nghiệp của bạn hay không? [ DONATE ] |
Alldatasheet là | Quảng cáo | Liên lạc với chúng tôi | Chính sách bảo mật | Liên kết đến bảng dữ liệu | Trao đổi link | Tìm kiếm theo nhà sản xuất All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |