| công cụ tìm kiếm bảng dữ liệu linh kiện điện tử |
|
LPC55S2X bảng dữ liệu(PDF) 8 Page - NXP Semiconductors |
|
|
|||||||||||||||||||||||||||||
LPC55S2X bảng dữ liệu(HTML) 8 Page - NXP Semiconductors |
|
8 / 132 page ![]() NXP Semiconductors LPC55S2x/LPC552x 32-bit Arm Cortex®-M33 microcontroller 6 Pinning information 6.1 Pin description Table 4 shows the pin functions available on each pin, and for each package. These functions are selectable using the IOCON control registers. Some functions, such as ADC or comparator inputs, are available only on specific pins when digital functions are disabled on those pins. By default, the GPIO function is selected except on pins PIO0_11 an PIO0_12, which are the serial wire debug pins. This allows debug to operate through reset. All pins have all pull-ups, pull-downs, and inputs turned off at reset except PIO0_2, PIO0_5, PIO0_11, PIO0_12, PIO0_13 and PIO0_14 pins. This prevents power loss through pins prior to software configuration. Due to special pin functions, some pins have a different reset configuration. PIO0_5 and PIO0_12 pins have internal pull-up enabled by default, and PIO0_2 and PIO0_11 have internal pull-down enabled by default. PIO0_13 and PIO0_14 are true open drain pins. Refer to pin description table for default reset configuration. The state of port pin PIO0_5 at Reset determines the boot source of the part or if the handler is invoked. The external reset pin or 3 wake-up pins can trigger a wake-up from deep power-down mode. For the wake-up pins, do not assign any function to this pin if it will be used as a wake-up input when using deep power-down mode. If not in deep power-down mode, a function can be assigned to this pin. If the pin is used for wake-up, it should be pulled HIGH externally before entering deep power-down mode. A LOW-going pulse as short as 50 ns causes the chip to exit deep power-down mode wakes up the part. The JTAG functions TRST, TCK, TMS, TDI, and TDO, are selected on pins PIO0_2 to PIO0_6 by hardware when the part is in boundary scan mode. The JTAG functions cannot be used for debug mode. Symbol 59 pin VFBGA 64 pin HTQFP 98 pin VFBGA 100 pin HLQFP Reset state [1] Type Function # Description I/O; AI 0 PIO0_0/ACMP0_A General-purpose digital input/output pin. Comparator 0, input A if the DIGIMODE bit is set to 0 and ANAMODE is set to 1 in the IOCON register for this pin. 1 R Reserved. I/O 2 FC3_SCK Flexcomm 3: USART, SPI, or I2S clock. O 3 CTIMER0_MAT0 32-bit CTimer0 match output 0. I 4 SCT0_GPI0 Pin input 0 to SCTimer/PWM. 5 R Reserved. I 6 SD1_CARD_INT_N SD/MMC 1 card interrupt. PIO0_0/ ACMP0_A J8 36 L12 54 [2] Z 7 R Reserved. Table 3. Pin description LPC55S2X_LPC552X All information provided in this document is subject to legal disclaimers. © 2024 NXP B.V. All rights reserved. Data sheet Rev. 2.3 — 29 August 2024 Document feedback 8 / 132 |
|
Link URL |
| Cho đến nay ALLDATASHEET có giúp ích cho doanh nghiệp của bạn hay không? [ DONATE ] |
Alldatasheet là | Quảng cáo | Liên lạc với chúng tôi | Chính sách bảo mật | Liên kết đến bảng dữ liệu | Trao đổi link | Tìm kiếm theo nhà sản xuất All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |