| công cụ tìm kiếm bảng dữ liệu linh kiện điện tử |
|
CY8C58LP bảng dữ liệu(PDF) 18 Page - Cypress Semiconductor |
|
|
|||||||||||||||||||||||||||||
CY8C58LP bảng dữ liệu(HTML) 18 Page - Cypress Semiconductor |
|
18 / 122 page ![]() PRELIMINARY PSoC® 5LP: CY8C58LP Family Datasheet Document Number: 001-84932 Rev. ** Page 18 of 122 5.5 Nonvolatile Latches (NVLs) PSoC has a 4-byte array of nonvolatile latches (NVLs) that are used to configure the device at reset. The NVL register map is shown in Table 5-3.. The details for individual fields and their factory default settings are shown in Table 5-3:. Although PSoC Creator provides support for modifying the device configuration NVLs, the number of NVL erase/write cycles is limited – see “Nonvolatile Latches (NVL)” on page 105. Table 5-2. Device Configuration NVL Register Map Register Address 7 6 5 4 3 2 1 0 0x00 PRT3RDM[1:0] PRT2RDM[1:0] PRT1RDM[1:0] PRT0RDM[1:0] 0x01 PRT12RDM[1:0] PRT6RDM[1:0] PRT5RDM[1:0] PRT4RDM[1:0] 0x02 XRESMEN PRT15RDM[1:0] 0x03 DIG_PHS_DLY[3:0] ECCEN DPS[1:0] CFGSPEED Table 5-3. Fields and Factory Default Settings Field Description Settings PRTxRDM[1:0] Controls reset drive mode of the corresponding IO port. See “Reset Configuration” on page 35. All pins of the port are set to the same mode. 00b (default) - high impedance analog 01b - high impedance digital 10b - resistive pull up 11b - resistive pull down XRESMEN Controls whether pin P1[2] is used as a GPIO or as an external reset. See “Pin Descriptions” on page 9, XRES description. 0 (default) - GPIO 1 - external reset CFGSPEED Controls the speed of the IMO-based clock during the device boot process, for faster boot or low-power operation 0 (default) - 12 MHz IMO 1 - 48 MHz IMO DPS{1:0] Controls the usage of various P1 pins as a debug port. See “Programming, Debug Interfaces, Resources” on page 57. 00b - 5-wire JTAG 01b (default) - 4-wire JTAG 10b - SWD 11b - debug ports disabled ECCEN Controls whether ECC flash is used for ECC or for general configuration and data storage. See “Flash Program Memory” on page 17. 0 (default) - ECC disabled 1 - ECC enabled DIG_PHS_DLY[3:0] Selects the digital clock phase delay. See the TRM for details. |
|
Link URL |
| Cho đến nay ALLDATASHEET có giúp ích cho doanh nghiệp của bạn hay không? [ DONATE ] |
Alldatasheet là | Quảng cáo | Liên lạc với chúng tôi | Chính sách bảo mật | Liên kết đến bảng dữ liệu | Trao đổi link | Tìm kiếm theo nhà sản xuất All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |