CY8C58LP datasheet(45/122 Pages) CYPRESS

45 / 122 page

PRELIMINARY

PSoC® 5LP: CY8C58LP Family

Datasheet

Document Number: 001-84932 Rev. **

Page 45 of 122

through the DSI. Each of the four instances has a compare

output, terminal count output (optional complementary compare

output), and programmable interrupt request line. The

Timer/Counter/PWMs are configurable as free running, one shot,

or Enable input controlled. The peripheral has timer reset and

capture inputs, and a kill input for control of the comparator

outputs. The peripheral supports full 16-bit capture.

Timer/Counter/PWM features include:

■ 16-bit timer/counter/PWM (down count only)

■ Selectable clock source

■ PWM comparator (configurable for LT, LTE, EQ, GTE, GT)

■ Period reload on start, reset, and terminal count

■ Interrupt on terminal count, compare true, or capture

■ Dynamic counter reads

■ Timer capture mode

■ Count while enable signal is asserted mode

■ Free run mode

■ One-shot mode (stop at end of period)

■ Complementary PWM outputs with deadband

■ PWM output kill

Figure 7-17. Timer/Counter/PWM

7.8 I2C

The I2C peripheral provides a synchronous two wire interface

designed to interface the PSoC device with a two wire I2C serial

communication bus. It is compatible[12] with I2C Standard-mode,

Fast-mode, and Fast-mode Plus devices as defined in the NXP

I2C-bus specification and user manual (UM10204). The I2C bus

I/O may be implemented with GPIO or SIO in open-drain modes.

Additional I2C interfaces can be instantiated using Universal

Digital Blocks (UDBs) in PSoC Creator, as required.

To eliminate the need for excessive CPU intervention and

overhead, I2C specific support is provided for status detection

and generation of framing bits. I2C operates as a slave, a master,

or multimaster (Slave and Master). In slave mode, the unit

always listens for a start condition to begin sending or receiving

data. Master mode supplies the ability to generate the Start and

Stop conditions and initiate transactions. Multimaster mode

provides clock synchronization and arbitration to allow multiple

masters on the same bus. If Master mode is enabled and Slave

mode is not enabled, the block does not generate interrupts on

externally generated Start conditions. I2C interfaces through the

DSI routing and allows direct connections to any GPIO or SIO

pins.

I2C provides hardware address detect of a 7-bit address without

CPU intervention. Additionally the device can wake from low

power modes on a 7-bit hardware address match. If wakeup

functionality is required, I2C pin connections are limited to the

two special sets of SIO pins.

I2C features include:

■ Slave and master, transmitter, and receiver operation

■ Byte processing for low CPU overhead

■ Interrupt or polling CPU interface

■ Support for bus speeds up to 1 Mbps

■ 7 or 10-bit addressing (10-bit addressing requires firmware

support)

■ SMBus operation (through firmware support - SMBus

supported in hardware in UDBs)

■ 7-bit hardware address compare

■ Wake from low power modes on address match

■ Glitch filtering (active and alternate-active modes only)

Data transfers follow the format shown in Figure 7-18. After the

START condition (S), a slave address is sent. This address is 7

bits long followed by an eighth bit which is a data direction bit

(R/W) - a 'zero' indicates a transmission (WRITE), a 'one'

indicates a request for data (READ). A data transfer is always

terminated by a STOP condition (P) generated by the master.

However, if a master still wishes to communicate on the bus, it

can generate a repeated START condition (Sr) and address

another slave without first generating a STOP condition. Various

combinations of read/write formats are then possible within such

a transfer.

Figure 7-18. I2C Complete Transfer Timing

Timer / Counter /

PWM 16-bit

Clock

Reset

Enable

Capture

Kill

IRQ

Compare

TC / Compare!

Note

12. The I2C peripheral is non-compliant with the NXP I2C specification in the following areas: analog glitch filter, I/O VOL/IOL, I/O hysteresis. The I2C Block has a digital

glitch filter (not available in sleep mode). The Fast-mode minimum fall-time specification can be met by setting the I/Os to slow speed mode. See the I/O Electrical

Specifications in “Inputs and Outputs” section on page 69 for details.

SDA

SCL

1 - 7

START

Condition

ADDRESS

R/W

ACK

DATA

ACK

DATA

ACK

STOP

Condition

CY8C58LP bảng dữ liệu(PDF) 45 Page - Cypress Semiconductor

CY8C58LP bảng dữ liệu(HTML) 45 Page - Cypress Semiconductor

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

bảng dữ liệu tải về

Link URL