| công cụ tìm kiếm bảng dữ liệu linh kiện điện tử |
|
HD64F2149YV bảng dữ liệu(PDF) 137 Page - Renesas Technology Corp |
|
|
|||||||||||||||||||||||||||||
HD64F2149YV bảng dữ liệu(HTML) 137 Page - Renesas Technology Corp |
|
137 / 1075 page ![]() Section 5 Interrupt Controller Rev. 3.00 Jan 18, 2006 page 109 of 1044 REJ09B0280-0300 Bits 7 to 0—IRQ7 to IRQ0 Flags (IRQ7F to IRQ0F): These bits indicate the status of IRQ7 to IRQ0 interrupt requests. Bit n IRQnF Description 0 [Clearing conditions] (Initial value) • Cleared by reading IRQnF when set to 1, then writing 0 in IRQnF • When interrupt exception handling is executed while low-level detection is set (IRQnSCB = IRQnSCA = 0) and IRQn input is high* • When IRQn interrupt exception handling is executed while falling, rising, or both-edge detection is set (IRQnSCB = 1 or IRQnSCA = 1)* 1 [Setting conditions] • When IRQn input goes low when low-level detection is set (IRQnSCB = IRQnSCA = 0) • When a falling edge occurs in IRQn input while falling edge detection is set (IRQnSCB = 0, IRQnSCA = 1) • When a rising edge occurs in IRQn input while rising edge detection is set (IRQnSCB = 1, IRQnSCA = 0) • When a falling or rising edge occurs in IRQn input while both-edge detection is set (IRQnSCB = IRQnSCA = 1) (n = 7 to 0) Note: * When a product, in which a DTC is incorporated, is used in the following settings, the corresponding flag bit is not automatically cleared even when exception handing, which is a clear condition, is executed and the bit is held at 1. (1) When DTCEA3 is set to 1(ADI is set to an interrupt source), of IRQ4F flag is not automatically cleared. (2) When DTCEA2 is set to 1(ICIA is set to an interrupt source), clearing of IRQ5F flag is not automatically cleared. (3) When DTCEA1 is set to 1(ICIB is set to an interrupt source), clearing of IRQ6F flag is not automatically cleared. (4) When DTCEA0 is set to 1(OCIA is set to an interrupt source), clearing of IRQ7F flag is not automatically cleared. When activation interrupt sources of DTC and IRQ interrupts are used with the above combinations, clear the interrupt flag by software in the interrupt handling routine of the corresponding IRQ. |
|
Link URL |
| Cho đến nay ALLDATASHEET có giúp ích cho doanh nghiệp của bạn hay không? [ DONATE ] |
Alldatasheet là | Quảng cáo | Liên lạc với chúng tôi | Chính sách bảo mật | Liên kết đến bảng dữ liệu | Trao đổi link | Tìm kiếm theo nhà sản xuất All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |