| công cụ tìm kiếm bảng dữ liệu linh kiện điện tử |
|
TMP93CS44 bảng dữ liệu(PDF) 9 Page - Toshiba Semiconductor |
|
|
|||||||||||||||||||||||||||||
TMP93CS44 bảng dữ liệu(HTML) 9 Page - Toshiba Semiconductor |
|
9 / 224 page ![]() TMP93CS44/S45 2004-02-10 93CS44-7 Table 2.2.3 Pin Names and Functions (3/3) Pin Names Number of Pins I/O Functions I/O Port 70: I/O port (High current output available) P70 WAIT 1 Input WAIT: Pin used to request CPU bus wait (It is active in (1 + N) WAIT mode. Set by the bus-width/wait control register) P71 to P77 7 I/O Port 71 to Port 77: I/O port (High current output available) AVCC 1 Input Power supply pin for AD converter AVSS 1 Input GND pin for AD converter (0 V) VREFH 1 Input Pin for high-level reference voltage input to AD converter VREFL 1 Input Pin for low-level reference voltage input to AD converter NMI 1 Input Non-maskable interrupt request pin: Interrupt request pin with falling edge. Can also be operated at falling and rising edges by program. X1 1 Input High-frequency oscillator connecting pin X2 1 Output High-frequency oscillator connecting pin RESET 1 Input Reset: Initializes TMP93CS44/S45. (with pull-up resistor) ALE 1 Output Address latch enable. Can be disabled for reducing noise. CLK 1 Output Clock output: Outputs “fSYS ÷ 2” clock. Pulled-up during reset. Can be disabled for reducing noise. EA 1 Input External access: “0” should be inputted with TMP93CS45. “1” should be inputted with TMP93CS44. AM8/ 16 AM 1 Input Address mode: Selects external data bus width. (The case of TMP93CS44) “1” should be inputted. The data bus width for external access is set by chip select/WAIT control register, port 1 control register. (The case of TMP93CS45) “0” should be inputted with fixed 16-bit bus width or 16-bit bus interlarded with 8-bit bus. “1” should be inputted with fixed 8-bit bus width. VCC 2 Input Power supply pin (All VCC pins should be connected with GND (0 V).) VSS 2 Input GND pin (0 V) (All VSS pins should be connected with GND (0 V).) TEST1/TEST2 2 Output/Input TEST1 should be connected with TEST2 pin. Do not connect to any other pins. Note: Built-in pull-up resistors can be released from the pins other than the RESET pin by software. |
|
Link URL |
| Cho đến nay ALLDATASHEET có giúp ích cho doanh nghiệp của bạn hay không? [ DONATE ] |
Alldatasheet là | Quảng cáo | Liên lạc với chúng tôi | Chính sách bảo mật | Liên kết đến bảng dữ liệu | Trao đổi link | Tìm kiếm theo nhà sản xuất All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |