PXAS30 datasheet(41/52 Pages) PHILIPS

41 / 52 page

Philips Semiconductors

Preliminary specification

XA-S3

XA 16-bit microcontroller

32 K/1 K OTP/ROM/ROMless, 8-channel 8-bit A/D, low voltage (2.7 V–5.5 V),

I2C, 2 UARTs, 16 MB address range

2000 Dec 01

AC ELECTRICAL CHARACTERISTICS (3 V RANGE) (continued)

This set of parameters is referenced to the XA-S3 clock output.

SYMBOL

FIGURE

PARAMETER

LIMITS

UNIT

SYMBOL

FIGURE

PARAMETER

MIN

MAX

UNIT

Address Cycle

tCHLH

CLKOUT rising edge to ALE rising edge

–

tCLLL

CLKOUT falling edge to ALE falling edge

–

tCHAV

CLKOUT rising edge to address valid

–

tCHAX

CLKOUT rising edge to address changing (hold time)

–

Code Read Cycle

tCHPL

CLKOUT rising edge to PSEN asserted

–

tCHPH

CLKOUT rising edge to PSEN de-asserted

–

tIVCH

Instruction valid to CLKOUT rising edge (setup time)

–

tCHIX

CLKOUT rising edge to instruction changing (hold time)

–

tCHIZ

CLKOUT rising edge to Bus 3-State (code read)

–

tC–8

Data Read Cycle

tCHRL

CLKOUT rising edge to RD asserted

–

tCHRH

CLKOUT rising edge to RD de-asserted

–

tDVCH

Data valid to CLKOUT rising edge (setup time)

–

tCHDX

CLKOUT rising edge to Data changing (hold time)

–

tCHDZ

CLKOUT rising edge to Bus 3-State (data read)

–

tC–8

Data Write Cycle

tCHWL

CLKOUT falling edge to WR asserted

–

tCHWH

CLKOUT rising edge to WR de-asserted

–

tQVCH

Data valid to CLKOUT rising edge (setup time)

–

tCHQX

CLKOUT rising edge to Data changing (hold time)

–

Wait Input

tCHWTH

WAIT valid prior to CLKOUT rising edge8

NOTES:

1. Load capacitance for all outputs = 50 pF.

2. Variables V1 through V13 reflect programmable bus timing, which is programmed via the Bus Timing registers (BTRH and BTRL). Refer to

the

XA User Guide for details of the bus timing settings.

V1)

This variable represents the programmed width of the ALE pulse as determined by the ALEW bit in the BTRL register. V1 = 0.5 if the

ALEW bit = 0, and 1.5 if the ALEW bit = 1.

V2)

This variable represents the programmed width of the PSEN pulse as determined by the CR1 and CR0 bits or the CRA1, CRA0, and

ALEW bits in the BTRL register.

–

For a bus cycle with no ALE, V2 = 1 if CR1/0 = 00, 2 if CR1/0 = 01, 3 if CR1/0 = 10, and 4 if CR1/0 = 11. Note that during burst

mode code fetches, PSEN does not exhibit transitions at the boundaries of bus cycles. V2 still applies for the purpose of

determining peripheral timing requirements.

–

For a bus cycle with an ALE, V2 = the total bus cycle duration (2 if CRA1/0 = 00, 3 if CRA1/0 = 01, 4 if CRA1/0 = 10, and 5 if

CRA1/0 = 11) minus the number of clocks used by ALE (V1 + 0.5) = 2.

Example: if CRA1/0 = 10 and ALEW = 1, the V2 = 4 – (1.5 + 0.5) = 2.

V3)

This variable represents the programmed length of an entire code read cycle with ALE. This time is determined by the CRA1 and

CRA0 bits in the BTRL register. V3 = the total bus cycle duration (2 if CRA1/0 = 00, 3 if CRA1/0 = 01, 4 if CRA1/0 = 10, and

5 if CRA1/0 = 11).

V4)

This variable represents the programmed length of an entire code read cycle with no ALE. This time is determined by the CR1 and

CR0 bits in the BTRL register. V4 = 1 if CR1/0 = 00, 2 if CR1/0 = 01, 3 if CR1/0 = 10, and 4 if CR1/0 = 11.

V5)

This variable represents the programmed length of an entire data read cycle with no ALE. This time is determined by the DR1 and

DR0 bits in the BTRH register. V5 = 1 if DR1/0 = 00, 2 if DR1/0 = 01, 3 if DR1/0 = 10, and 4 if DR1/0 = 11.

V6)

This variable represents the programmed length of an entire data read cycle with ALE. The time is determined by the DRA1 and

DRA0 bits in the BTRH register. V6 = the total bus cycle duration (2 if DRA1/0 = 00, 3 if DRA1/0 = 01, 4 if DRA1/0 = 10, and

5 if DRA1/0 = 11).

PXAS30 bảng dữ liệu(PDF) 41 Page - NXP Semiconductors

PXAS30 bảng dữ liệu(HTML) 41 Page - NXP Semiconductors

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52

bảng dữ liệu tải về

Link URL