PIC18F44J10-ESLASHML datasheet(159/358 Pages) MICROCHIP

159 / 358 page

Preliminary

DS39682C-page 157

PIC18F45J10 FAMILY

SSPxCON1: MSSPx CONTROL REGISTER 1 (I2C™ MODE)

R/W-0

WCOL

SSPOV

SSPEN

CKP

SSPM3

SSPM2

SSPM1

SSPM0

bit 7

bit 0

bit 7

WCOL: Write Collision Detect bit

In Master Transmit mode:

= A write to the SSPxBUF register was attempted while the I2C conditions were not valid for a

transmission to be started (must be cleared in software)

= No collision

In Slave Transmit mode:

= The SSPxBUF register is written while it is still transmitting the previous word (must be

cleared in software)

= No collision

In Receive mode (Master or Slave modes):

This is a “don’t care” bit.

bit 6

SSPOV: Receive Overflow Indicator bit

In Receive mode:

= A byte is received while the SSPxBUF register is still holding the previous byte (must be

cleared in software)

= No overflow

In Transmit mode:

This is a “don’t care” bit in Transmit mode.

bit 5

SSPEN: Master Synchronous Serial Port Enable bit

= Enables the serial port and configures the SDAx and SCLx pins as the serial port pins

= Disables serial port and configures these pins as I/O port pins

Note:

When enabled, the SDAx and SCLx pins must be properly configured as input or

output.

bit 4

CKP: SCKx Release Control bit

In Slave mode:

= Release clock

= Holds clock low (clock stretch), used to ensure data setup time

In Master mode:

Unused in this mode.

bit 3-0

SSPM3:SSPM0: Master Synchronous Serial Port Mode Select bits

1111

= I2C Slave mode, 10-bit address with Start and Stop bit interrupts enabled

1110

= I2C Slave mode, 7-bit address with Start and Stop bit interrupts enabled

1011

= I2C Firmware Controlled Master mode (Slave Idle)

1000

= I2C Master mode, clock = FOSC/(4 * (SSPxADD + 1))

0111

= I2C Slave mode, 10-bit address

0110

= I2C Slave mode, 7-bit address

Bit combinations not specifically listed here are either reserved or implemented in SPI mode only.

Legend:

R = Readable bit

W = Writable bit

U = Unimplemented bit, read as ‘0’

-n = Value at POR

‘1’ = Bit is set

‘0’ = Bit is cleared

x = Bit is unknown

PIC18F44J10-E/ML bảng dữ liệu(PDF) 159 Page - Microchip Technology

PIC18F44J10-E/ML bảng dữ liệu(HTML) 159 Page - Microchip Technology

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

bảng dữ liệu tải về

Link URL