ATAM862 datasheet(47/110 Pages) ATMEL

47 / 110 page

4554E–4BMCU–05/06

ATAM862-3

22.8

Timer 2

8-/12-bit Timer for:

• Interrupt, square-wave, pulse and duty cycle generation

• Baud-rate generation for the internal shift register

• Manchester and Biphase modulation together with the SSI

• Carrier frequency generation and modulation together with the SSI

Timer 2 can be used as an interval timer for interrupt generation, as signal generator or as

baud-rate generator and modulator for the serial interface. It consists of a 4-bit and an 8-bit up

counter stage which both have compare registers. The 4-bit counter stages of Timer 2 are cas-

cadable as a 12-bit timer or as an 8-bit timer with 4-bit prescaler. The timer can also be

configured as an 8-bit timer and separate a 4-bit prescaler.

The Timer 2 input can be supplied via the system clock, the external input clock (T2I), the Timer

1 output clock, the Timer 3 output clock or the shift clock of the serial interface. The external

input clock T2I is not synchronized with SYSCL. Therefore, it is possible to use Timer 2 with a

higher clock speed than SYSCL. Furthermore, with that input clock the Timer 2 operates in the

power-down mode SLEEP (CPU core -> sleep and OSC-Stop -> yes) as well as in the

POWER-DOWN (CPU core -> sleep and OSC-Stop -> no). All other clock sources supply no

clock signal in SLEEP if NSTOP = 0. The 4-bit counter stages of Timer 2 have an additional

clock output (POUT).

Its output has a modulator stage that allows the generation of pulses as well as the generation

and modulation of carrier frequencies. The Timer 2 output can modulate with the shift register

data output to generate Biphase- or Manchester code.

If the serial interface is used to modulate a bitstream, the 4-bit stage of Timer 2 has a special

task. The shift register can only handle bitstream lengths divisible by 8. For other lengths, the

4-bit counter stage can be used to stop the modulator after the right bit-count is shifted out.

If the timer is used for carrier frequency modulation, the 4-bit stage works together with an addi-

tional 2-bit duty cycle generator like a 6-bit prescaler to generate carrier frequency and duty

cycle. The 8-bit counter is used to enable and disable the modulator output for a programmable

count of pulses.

For programming the time interval, the timer has a 4-bit and an 8-bit compare register. For pro-

gramming the timer function, it has four mode and control registers. The comparator output of

stage 2 is controlled by a special compare mode register (T2CM). This register contains mask

bits for the actions (counter reset, output toggle, timer interrupt) which can be triggered by a

compare match event or the counter overflow. This architecture enables the timer function for

various modes.

The Timer 2 has a 4-bit compare register (T2CO1) and an 8-bit compare register (T2CO2). Both

these compare registers are cascadable as a 12-bit compare register, or 8-bit compare register

and 4-bit compare register.

For 12-bit compare data value:

m = x +1

≤x ≤4095

For 8-bit compare data value:

n = y +1

≤y ≤255

For 4-bit compare data value:

l = z +1

≤z ≤15

ATAM862 bảng dữ liệu(PDF) 47 Page - ATMEL Corporation

ATAM862 bảng dữ liệu(HTML) 47 Page - ATMEL Corporation

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

bảng dữ liệu tải về

Link URL