| công cụ tìm kiếm bảng dữ liệu linh kiện điện tử |
|
VSC8658 bảng dữ liệu(PDF) 44 Page - Microsemi Corporation |
|
|
|||||||||||||||||||||||||||||
VSC8658 bảng dữ liệu(HTML) 44 Page - Microsemi Corporation |
|
44 / 95 page ![]() Configuration VMDS-10242 VSC8658 Datasheet Revision 4.1 36 Note If bit 18.1 is set to 1 in this register, automatic exchange of next pages is disabled, and control is returned to the user through the SMI after the base page is exchanged. The user then must send the correct sequence of next pages to the link partner, determine the common capabilities, and force the device into the correct configuration following the successful exchange of pages. 5.2.16 Reserved Main Address Space The bits in register 19, register 20, and register 21 (0x13, 0x14, and 0x15, respectively) are reserved. 5.2.17 Extended Control and Status The bits in register 22 provide additional device control and readouts. The following table shows the settings available. 4 Disable polarity correction R/W This is a sticky bit. 1 = Disable polarity inversion correction on each subchannel. 0 3 Parallel detect control R/W This is a sticky bit. 1 = Do not ignore advertised ability. 0 = Ignore advertised ability. 1 2Reserved RO 1 Disable automatic 1000BASE-T next page exchange R/W This is a sticky bit. 1 = Disable automatic 1000BASE-T next page exchanges. 0 0 CLKOUT output enable R/W This is a sticky bit. 1 = Enable clock output pin. CMODE Table 26 • Extended Control and Status, Address 22 (0x16) Bit Name Access Description Default 15 Force 10BASE-T link high R/W This is a sticky bit. 1 = Bypass link integrity test. 0 = Enable link integrity test. 0 14 Jabber detect disable R/W This is a sticky bit. 1 = Disable jabber detect. 0 13 Disable 10BASE-T echo R/W This is a sticky bit. 1 = Disable 10BASE-T echo. 1 12 Reserved RO 11:10 10BASE-T squelch control R/W This is a sticky bit. 00 = Normal squelch. 01 = Low squelch. 10 = High squelch. 11 = Reserved. 00 9 Sticky reset enable R/W This is a super-sticky bit. 1 = Enabled. 1 8 EOF Error RO This bit is self-clearing. 1 = EOF error detected. 0 7 10BASE-T disconnect state RO This bit is self-clearing. 1 = 10BASE-T link disconnect detected. 0 Table 25 • Bypass Control, Address 18 (0x12) (continued) Bit Name Access Description Default |
|
Link URL |
| Cho đến nay ALLDATASHEET có giúp ích cho doanh nghiệp của bạn hay không? [ DONATE ] |
Alldatasheet là | Quảng cáo | Liên lạc với chúng tôi | Chính sách bảo mật | Liên kết đến bảng dữ liệu | Trao đổi link | Tìm kiếm theo nhà sản xuất All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |