ADRV9010BBCZ datasheet(20/115 Pages) AD

20 / 115 page

ADRV9010

Data Sheet

Rev. E | Page 20 of 115

ABSOLUTE MAXIMUM RATINGS

Table 6.

Parameter

Rating

VDDA_1P8 to VSSA

−0.3 V to +2.2 V

VDDA_1P3 to VSSA

−0.2 V to +1.5 V

VDDA_1P0, VDIG_1P0 to VSSD, VSSA

−0.2 V to +1.2 V

VIF Referenced Logic Inputs and

Outputs to VSSD

−0.3 V to VIF + 0.3 V

JESD204B Logic Outputs to VSSA

−0.3 V to VSER_1P0

JESD204B Logic Inputs to VSSA

−0.3 V to VDES_1P0

Input Current to Any Pin Except Supplies

±10 mA

Maximum Input Power into RF Ports

See Table 8 for limits

vs. survival time

Junction Temperature Range1

−40°C to +110°C

Storage Temperature Range

−65°C to +150°C

1 The maximum junction temperature for continuous operation is 110°C. See

the Junction Temperature section for more details.

Stresses at or above those listed under Absolute Maximum

Ratings may cause permanent damage to the product. This is a

stress rating only; functional operation of the product at these

or any other conditions above those indicated in the operational

section of this specification is not implied. Operation beyond the

maximum operating conditions for extended periods may

affect product reliability.

JUNCTION TEMPERATURE

The maximum junction temperature for continuous operation

is 110°C. Although operation up to 125°C is supported,

specification compliance is only guaranteed up to 110°C. To

avoid a reduction in operating lifetime by operating above 110°C,

the device must operate at a temperature less than 110°C for a

period (tUNITS) determined by the following equation:

tUNITS < 110 = (AFT > 110 − 1)/(1 − AFT < 110)

where AFT > 110 and AFT < 110 are acceleration factors obtained

from Table 7.

For example, if the device operates at 125°C for 1 hour, expected

device lifetime is maintained if the device operates at 100°C for

4.5 hours to offset the time operating above 110°C.

Table 7. Acceleration Factors for High Temperature Operation

Operating Junction Temperature (°C)

Acceleration Factor (AF)

125

3.75

120

2.44

115

1.57

110

1.00

105

0.63

100

0.39

0.24

0.14

Table 8. Maximum Input Power into RF Ports vs. Lifetime

RF Port Input Power,

CW Signal (dBm)

Lifetime

Gain = −30 dB

Gain = 0 dB

>10 years

20,000 hours

>10 years

14 hours

>10 years

110 minutes

>7 years

60 minutes

REFLOW PROFILE

The ADRV9010 reflow profile is in accordance with the JEDEC

JESD20 criteria for Pb-free devices. The maximum reflow

temperature is 260°C.

THERMAL RESISTANCE

Thermal resistance values specified in Table 9 are calculated

based on JEDEC specifications (unless specified otherwise) and

should be used in compliance with JESD51-12. Note that using

enhanced heat removal techniques (PCB, heat sink, air flow,

and so forth) improves thermal resistance.

θJA is the natural convection junction to ambient thermal

resistance measured in a one cubic foot sealed enclosure.

θJC is the junction to case thermal resistance.

Table 9. Thermal Resistance Values

Package Type

θJA

θJC

Unit

BC-289-3

14.8

0.03

(°C/W)

ESD CAUTION

ADRV9010BBCZ bảng dữ liệu(PDF) 20 Page - Analog Devices

ADRV9010BBCZ bảng dữ liệu(HTML) 20 Page - Analog Devices

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

bảng dữ liệu tải về

Link URL