AT90LS8535-4AI datasheet(4/127 Pages) ATMEL

4 / 127 page

AT90S/LS8535

1041H–11/01

The AVR core combines a rich instruction set with 32 general-purpose working regis-

ters. All the 32 registers are directly connected to the Arithmetic Logic Unit (ALU),

allowing two independent registers to be accessed in one single instruction executed in

one clock cycle. The resulting architecture is more code efficient while achieving

throughputs up to ten times faster than conventional CISC microcontrollers.

The AT90S8535 provides the following features: 8K bytes of In-System Programmable

Flash, 512 bytes EEPROM, 512 bytes SRAM, 32 general-purpose I/O lines, 32 general-

purpose working registers, Real-time Clock (RTC), three flexible timer/counters with

compare modes, internal and external interrupts, a programmable serial UART, 8-chan-

nel, 10-bit ADC, programmable Watchdog Timer with internal oscillator, an SPI serial

port and three software-selectable power-saving modes. The Idle Mode stops the CPU

while allowing the SRAM, timer/counters, SPI port and interrupt system to continue

functioning. The Power-down mode saves the register contents but freezes the oscilla-

tor, disabling all other chip functions until the next interrupt or hardware reset. In Power

Save Mode, the timer oscillator continues to run, allowing the user to maintain a timer

base while the rest of the device is sleeping.

The device is manufactured using Atmel’s high-density nonvolatile memory technology.

The On-chip ISP Flash allows the program memory to be reprogrammed in-system

through an SPI serial interface or by a conventional nonvolatile memory programmer.

By combining an 8-bit RISC CPU with In-System Programmable Flash on a monolithic

chip, the Atmel AT90S8535 is a powerful microcontroller that provides a highly flexible

and cost effective solution to many embedded control applications.

The AT90S8535 AVR is supported with a full suite of program and system development

tools including: C compilers, macro assemblers, program debugger/simulators, in-circuit

emulators and evaluation kits.

Pin Descriptions

VCC

Digital supply voltage.

GND

Digital ground.

Port A (PA7..PA0)

Port A is an 8-bit bi-directional I/O port. Port pins can provide internal pull-up resistors

(selected for each bit). The Port A output buffers can sink 20 mA and can drive LED dis-

plays directly. When pins PA0 to PA7 are used as inputs and are externally pulled low,

they will source current if the internal pull-up resistors are activated.

Port A also serves as the analog inputs to the A/D Converter.

The Port A pins are tri-stated when a reset condition becomes active, even if the clock is

not running.

Port B (PB7..PB0)

Port B is an 8-bit bi-directional I/O port with internal pull-up resistors. The Port B output

buffers can sink 20 mA. As inputs, Port B pins that are externally pulled low will source

current if the pull-up resistors are activated. Port B also serves the functions of various

special features of the AT90S8535 as listed on page 78.

The Port B pins are tri-stated when a reset condition becomes active, even if the clock is

not running.

Port C (PC7..PC0)

Port C is an 8-bit bi-directional I/O port with internal pull-up resistors. The Port C output

buffers can sink 20 mA. As inputs, Port C pins that are externally pulled low will source

AT90LS8535-4AI bảng dữ liệu(PDF) 4 Page - ATMEL Corporation

AT90LS8535-4AI bảng dữ liệu(HTML) 4 Page - ATMEL Corporation

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

bảng dữ liệu tải về

Link URL