| công cụ tìm kiếm bảng dữ liệu linh kiện điện tử |
|
DSP56857 bảng dữ liệu(PDF) 431 Page - Freescale Semiconductor, Inc |
|
|
|||||||||||||||||||||||||||||
DSP56857 bảng dữ liệu(HTML) 431 Page - Freescale Semiconductor, Inc |
|
431 / 662 page ![]() HI8 Host Port Host Interface Eight (HI8), Rev. 4 Freescale Semiconductor 16-5 16.3 Signal Descriptions 16.4 HI8 Host Port This section’s table details the HI8 pins and their functions. Additionally, the HI8 block diagram is located as Figure 16-1following the HI8 pins details in Table 16-1. Table 16-1. Host Interface 8 Signals HI8 Port Pin Signal Name Signal Type State During Reset of Stop Signal Description HD[0:7] HD0 - HD7 or (PB0 - PB7) Input /Output Input or Output Disconnected Internally Host Data Bus—This bidirectional data bus is used to transfer data between the Host Processor and the DSC, (HD0-HD7). Port B 0-7—These are GPIO pins when not configured for Host port use. HA[0:2] HA0 - HA2 or (PB8 - PB10) Input Input/Output Disconnected Internally Host Address—These inputs provide the address selection for the HI8 registers, (HA0-HA2). Port B 8-10—These are GPIO pins when not configured for Host port use. HRW / HRD HRW or HRD or (PB11) Input Input or Output Disconnected Internally Host Read/Write—When the HI8 is programmed to interface to a single data strobe host bus, this signal is the Read/Write input (HRW). When set low, the Host writes data to DSC. When set high, the Host reads data from DSC. Host Read Data Strobe—When the HI8 is programmed to interface to a double data strobe host bus, this signal is the Read Data strobe input (HRD), active low. Port B 11—This is a GPIO pin when not configured for Host port use. HDS / HWR HDS or HWR or (PB12) Input Input Input/Output Disconnected Internally Host Data Strobe—When the HI8 is programmed to interface to a single-data strobe host bus, this input enables a data transfer on the HI8 when HCS is set to low. Host Write Data Strobe—When the HI8 is programmed to interface to a double data strobe host bus and the HI8 function is selected, this active low signal is the Write Data Strobe input (HWR). Port B 12—This is a GPIO pin when not configured for Host port use. |
|
Link URL |
| Cho đến nay ALLDATASHEET có giúp ích cho doanh nghiệp của bạn hay không? [ DONATE ] |
Alldatasheet là | Quảng cáo | Liên lạc với chúng tôi | Chính sách bảo mật | Liên kết đến bảng dữ liệu | Trao đổi link | Tìm kiếm theo nhà sản xuất All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |