COM20022ITQFP datasheet(25/83 Pages) SMSC

25 / 83 page

10 Mbps ARCNET (ANSI 878.1) Controller with 2Kx8 On-Board RAM

Datasheet

SMSC COM20022I

Page 25

Rev. 08-18-03

DATASHEET

The following sequences show the data transfer for a DMA read and a DMA write. The transfer of data

between system memory and internal RAM functions as a memory to I/O DMA transfer. Since it is treated

as an I/O device, the COM20022I has to create the RAM address. Therefore the COM20022I’s address

pointers must be programmed before starting the DMA transfers.

5.1.4

DMA Data Transfer Sequence (I/O to Memory: Read A Packet)

step1: Set DMA-controller (ex. 8237)

step2: Set DRQPOL, TCPOL, DMAMD1 and DMAMD0 bits

>>Finished DMA SETUP

>>A packet received

step3: Set address, byte count and etc. of DMA controller

step4: Set pointer High and Low (RDDATA=1,AUTOINC=1, DMAEN=0)

step5: Read SID, DID, CP in the received packet

step6: Set DMAEN=1 (RDDATA=1, AUTOINC=1)

step7: DMAEND=1 in Mask REG.

step8: Set pointer = CP

>>DREQ is asserted by step8

>>Interrupt occurs upon finishing DMA

5.1.5

DMA Data Transfer Sequence (Memory to I/O: Write A Packet)

step1: Set DMA-controller (ex. 8237)

step2: Set DRQPOL, TCPOL, DMAMD1 and DMAMD0 bits

>>Finished DMA SETUP

step3: Set address, byte count and etc. of DMA controller

step4: Set pointer High and Low (RDDATA=0,AUTOINC=1, DMAEN = 0)

step5: Write SID,DID,CP in the sending packet

step6: Set DMAEN=1 (RDDATA=0, AUTOINC=1)

step7: DMAEND=1 in Mask REG.

step8: Set pointer = CP

>>DREQ is asserted by step8

>>Interrupt occurs upon finishing DMA transfer

step9: Write Enable Transmit command to command register

5.1.6

High Speed CPU Bus Timing Support

High speed CPU bus support was added to the COM20022I. The reasoning behind this is as follows: With

the Host interface in Non-multiplexed Bus mode, I/O address and Chip Select signals must be stable

before the read signal is active and remain after the read signal is inactive. But the High Speed CPU bus

timing doesn't adhere to these timings. For example, a RISC type single chip microcontroller (like the

HITACHI SH-1 series) changes I/O address at the same time as the read signal. Therefore, several

external logic ICs would be required to connect to this microcontroller.

In addition, the Diagnostic Status (DIAG) register is cleared automatically by reading itself. The internal

DIAG register read signal is generated by decoding the Address (A2-A0), Chip Select (nCS) and Read

(nRD) signals. The decoder will generate a noise spike at the above tight timing. The DIAG register is

cleared by the spike signal without reading itself. This is unexpected operation. Reading the internal RAM

and Next Id Register have the same mechanism as reading the DIAG register.

Therefore, the address decode and host interface mode blocks were modified to fit the above CPU

interface to support high speed CPU bus timing. In Intel CPU mode (nRD, nWR mode), 3 bit I/O address

(A2-A0) and Chip Select (nCS) are sampled internally by Flip-Flops on the falling edge of the internal

delayed nRD signal. The internal real read signal is the more delayed nRD signal. But the rising edge of

nRD doesn't delay. By this modification, the internal real address and Chip Select are stable while the

internal real read signal is active. Refer to Figure 5.7 on the following page.

COM20022ITQFP bảng dữ liệu(PDF) 25 Page - SMSC Corporation

COM20022ITQFP bảng dữ liệu(HTML) 25 Page - SMSC Corporation

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83

bảng dữ liệu tải về

Link URL